To Start the Welder

B-4

OPERATION

B-4

Return to Section TOC

Return to Master TOC

PROCEDURE FOR CHANGING DRIVE AND IDLE ROLL SETS

1.Turn off the power source.

2.Release the pressure on the idle roll by swinging the adjustable pressure arm down toward the back of the machine. Lift the cast idle roll assembly and allow it to sit in an upright position..

3.Remove the outside wire guide retaining plate by loosening the two large knurled screws.

4.Wiggle both the metal idle and drive rolls off of their plastic hubs.

5.Remove the inside wire guide plate.

6.Replace the drive and idle rolls and inside wire guide with a set marked for the new wire size. NOTE: Be sure that the gun liner and contact tip are also sized to match the selected wire size.

7.Manually feed the wire from the wire reel, over the drive roll groove and through the wire guide and then into the brass bushing of the gun and cable assembly.

8.Replace the outside wire guide retaining plate by tightening the two large knurled screws. Reposition the adjustable pressure arm to its original position to apply pressure. Adjust pressure as necessary.

WIRE REEL LOADING - READI-REELS, SPOOLS OR COILS

To Mount a 30 Lb. (14 kg) Readi-Reel Package (Using the Molded Plastic K363-P Readi-Reel Adapter:)

1.Open the Wire Drive Compartment Door.

2.Depress the Release Bar on the Retaining Collar and remove it from the spindle.

3.Place the Optional Adapter on the spindle

4.Re-install the Retaining Collar. Make sure that the Release Bar “pops up” and that the collar retainers fully engage the retaining ring groove on the spindle.

5.Rotate the spindle and adapter so the retaining spring is at the 12 o'clock position.

6.Position the Readi-Reel so that it will rotate in a direction when feed- ing so as to be de- reeled from top of the coil.

7.Set one of the Readi-Reel inside cage wires on the slot in the retain- ing spring tab.

8.Lower the Readi-Reel to depress the retaining spring and align the other inside cage wires with the grooves in the molded adapter.

9.Slide cage all the way onto the adapter until the retaining spring "pops up" fully.

CAUTION

CHECK TO BE SURE THE RETAINING SPRING HAS FULLY RETURNED TO THE LOCKING POSITION AND HAS SECURELY LOCKED THE READI-REEL CAGE IN PLACE. RETAINING SPRING MUST REST ON THE CAGE, NOT THE WELDING ELECTRODE.

-----------------------------------------------------------------------------------------------

10.To remove Readi-Reel from Adapter, depress retaining spring tab with thumb while pulling the Readi-Reel cage from the molded adapter with both hands. Do not remove adapter from spindle.

FIGURE B.2

To Mount 10 to 44 Lb. (4.5-20 kg) Spools (12"/300 mm Diameter) or 14Lb.(6 Kg) Innershield Coils:

(For 13-14 lb. (6 Kg) Innershield coils, a K435 Coil Adapter must be used).

1.Open the Wire Drive Compartment Door

2.Depress the Release Bar on the Retaining Collar and remove it from the spindle.

3.Place the spool on the spindle making certain the spindle brake pin enters one of the holes in the back side of the spool (Note: an arrow mark on the spindle lines up with the brake holding pin to assist in lining up a hole). Be certain the wire comes off the reel in a direction so as to de-reel from the top of the coil.

4.Re-install the Retaining Collar. Make sure that the Release Bar “pops up” and that the collar retainers fully engage the retaining ring groove on the spindle.

Turn the “Power Switch” switch to “ON”. This lights the red LED dis- play lights. With the desired voltage and wire speed selected, oper- ate the gun trigger for welder output and to energize the wire feed motor.

POWER MIG 200