Lincoln Electric SVM157-A service manual Control Board Replacement, Description

Page 61

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

F-27

TROUBLESHOOTING AND REPAIR

F-27

CONTROL BOARD REPLACEMENT

WARNING

Service and repair should only be performed by Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty. For your safety and to avoid electrical shock please observe all safety notes and precautions detailed throughout this manual.

If for any reason you do not understand the test procedures or are unable to perform the test/repairs safely, contact the Lincoln Electric service department for technical troubleshooting assistance before you proceed. Call 1-800-833- 9353(WELD).

DESCRIPTION

The following procedure will aid the technician in removing the control board for replacement.

MATERIALS NEEDED

5/16” Nutdriver

This procedure takes approximately 20 minutes to perform.

POWER MIG 200

Image 61

Contents Safety Depends on You Power MIGCalifornia Proposition 65 Warnings SafetyARC Rays can burn Electric Shock can killIii Cylinder may explode if damagedSûreté Pour Soudage a L’Arc Précautions DE SûretéMaster Table of Contents for ALL Sections Installation Section Table of ContentsTechnical Specifications Power MIG Installation3INSTALLATIONA-3 Figure A.1 Dual Voltage Machine Input Connections Figure A.2 Triple Voltage Machine Input Connections Output Polarity ConnectionsShielding GAS GUN and Cable InstallationCylinder may explode if damaged Operation Section B Operation SectionWear eye, ear and body protec- tion OperationWire Size Conversion Parts Wire Drive RollProduct Description Recommended Processes and EquipmentWire Reel Loading READI-REELS, Spools or Coils Procedure for Changing Drive and Idle Roll SetsTo Start the Welder Idle Roll Pressure Setting Feeding Wire Electrode Making a WeldWire Feed Overload Protection Avoiding Wire Feeding ProblemsFAN Control Input Line Voltage VariationsAccessories Section Drive Roll Kits AccessoriesK363P READI-REEL Adapter Dual Cylinder Mounting KIT K1702-1Adapter KIT and Spool GUN InstalledPower MIG Maintenance Section Maintenance Liner Removal and REPLACE- Ment Cause poor wire feedingThis screw should only be gently tightened Overtightening will split or collapse the linerEnglish Metric Description Size GUN Handle DisassemblyMaintenance Power MIG Theory of Operation Section Line SwitchTheory of Operation Motor Control Board Output Rectification Contactor and Control BoardFigure E.4 Optional Circuits Control BOARD, GUN Trigger and Wire Drive MotorThermal and Overload Protection Wirefeed Overload ProtectionPower MIG Troubleshooting and Repair Section F Troubleshooting and Repair SectionHow To Use Troubleshooting Guide Troubleshooting and RepairPC Board Troubleshooting Procedures Perform the Main Transformer Perform the Output Contactor Avoid contact with any portion These capacitors is toxicYour body Function Problems Tachometer Feedback Test Welding Problems Weld bead is narrow or ropy Make sure the welding proce Test Description Main Transformer TestMaterials Needed Main Transformer Test ON/OFF Power Switch will be hot during these testsX10 Input Voltage Test Points Table F.1. Test PointsWire Drive Motor and Tachometer Feedback Test Figure F.4. Plug J4 Test ProcedureTest for Supply Voltage to Tachometer Disconnect the main AC input power to the machineVDC Test for Feedback Voltage to Control BoardOutput Bridge Rectifier Test Output Bridge Rectifier Test Test ProcedureContactor Test Figure F.7. Contactor Terminals and Leads Contactor TestTypical Output Voltage Waveform Machine Loaded MAX TAP G Volts 10.0Normal Open Circuit Voltage Waveform MAX TAP G Volts 20.0Machine Loaded to 180 Amps AT 16 VDC Scope Settings Volts 20.0 Description Control Board ReplacementProcedure Control Board ReplacementWire Drive Motor Assembly Replacement Wire Drive Wire Drive Motor Assembly ReplacementBolt Gas Hose TOC Output Diode Bridge Rectifier Replacement Output Diode Bridge Rectifier Mounting Bracket Mounting Bolts Rectifier Power MIG Output Capacitors Replacement Figure F.14. Capacitor Bank Location Output Capacitors ReplacementLead Mounting Bolts Nuts & Lock washers Places Power MIG Main Transformer Replacement 41TROUBLESHOOTING and REPAIRF-41See Figure F.17 Main Transformer ReplacementFigure F.17. Leads X9, X10, 104B,104C, & H1B ReplacementX2 X3 X4 X5 X6 X7 Lead Power MIG FAN BLADE/MOTOR Replacement Perform the Output Capacitor Bank Removal Procedure FAN BLADE/MOTOR ReplacementOutput Contactor Replacement Figure F.24 Output Contactor ReplacementMounting Bolts Retest After Repair Table of Contents Electrical Diagrams Section Electrical DiagramsWiring Diagram Power MIG 200 208/230VSchematic Control PC Board G3851-1 PC Board ASSEMBLY-CONTROLSVM Error Reporting Form