Lincoln Electric SVM157-A Output Capacitors Replacement, Figure F.14. Capacitor Bank Location

Page 72

TOC

TOC

F-38	TROUBLESHOOTING AND REPAIR	F-38

OUTPUT CAPACITORS REPLACEMENT (Continued)

Return to Section

Return to Master

PROCEDURE

1.Using a 3/8” nutdriver, remove the lower right side case wraparound cover. See Figure F.14.

2.Locate capacitor bank. See Figure F.14.

3.Label and remove the five leads connected to the capacitor bank using a 1/2” wrench. Note washer position upon removal. See Figure

F.15.

4.Using a 3/8” nutdriver, remove the three capac- itor bank nuts and lock washers from the three mounting bolts. See Figure F.15.

5.Remove the capacitor bank assembly from the machine.

6.Place the new capacitor bank into its proper location inside the machine.

7.Replace the three 3/8” nuts and lock washers previously removed.

8.Using a 1/2” wrench, reconnect the five labeled leads and associated washers previously removed.

9.Replace the lower right side case wraparound cover previously removed.

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

FIGURE F.14. - CAPACITOR BANK LOCATION

LOWER RIGHT

CASE WRAPAROUND

COVER

CAPACITOR BANK

ASSEMBLY

POWER MIG 200

Image 72

Contents Power MIG Safety Depends on YouSafety California Proposition 65 WarningsElectric Shock can kill ARC Rays can burnCylinder may explode if damaged IiiPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcMaster Table of Contents for ALL Sections Table of Contents Installation SectionInstallation Technical Specifications Power MIG3INSTALLATIONA-3 Figure A.1 Dual Voltage Machine Input Connections Output Polarity Connections Figure A.2 Triple Voltage Machine Input ConnectionsGUN and Cable Installation Shielding GASCylinder may explode if damaged Operation Section Operation Section BOperation Wear eye, ear and body protec- tionWire Drive Roll Wire Size Conversion PartsProduct Description Recommended Processes and EquipmentProcedure for Changing Drive and Idle Roll Sets Wire Reel Loading READI-REELS, Spools or CoilsTo Start the Welder Feeding Wire Electrode Making a Weld Idle Roll Pressure SettingAvoiding Wire Feeding Problems Wire Feed Overload ProtectionFAN Control Input Line Voltage VariationsAccessories Section Accessories Drive Roll KitsK363P READI-REEL Adapter Dual Cylinder Mounting KIT K1702-1Installed Adapter KIT and Spool GUNPower MIG Maintenance Section Maintenance Cause poor wire feeding Liner Removal and REPLACE- MentThis screw should only be gently tightened Overtightening will split or collapse the linerGUN Handle Disassembly English Metric Description SizeMaintenance Power MIG Line Switch Theory of Operation SectionTheory of Operation Output Rectification Contactor and Control Board Motor Control BoardControl BOARD, GUN Trigger and Wire Drive Motor Figure E.4 Optional CircuitsWirefeed Overload Protection Thermal and Overload ProtectionPower MIG Troubleshooting and Repair Section Troubleshooting and Repair Section FTroubleshooting and Repair How To Use Troubleshooting GuidePC Board Troubleshooting Procedures Perform the Main Transformer Perform the Output Contactor These capacitors is toxic Avoid contact with any portionYour body Function Problems Tachometer Feedback Test Welding Problems Weld bead is narrow or ropy Make sure the welding proce Main Transformer Test Test DescriptionMaterials Needed ON/OFF Power Switch will be hot during these tests Main Transformer TestX10 Table F.1. Test Points Input Voltage Test PointsWire Drive Motor and Tachometer Feedback Test Test Procedure Figure F.4. Plug J4Disconnect the main AC input power to the machine Test for Supply Voltage to TachometerTest for Feedback Voltage to Control Board VDCOutput Bridge Rectifier Test Test Procedure Output Bridge Rectifier TestContactor Test Contactor Test Figure F.7. Contactor Terminals and LeadsVolts 10.0 Typical Output Voltage Waveform Machine Loaded MAX TAP GVolts 20.0 Normal Open Circuit Voltage Waveform MAX TAP GMachine Loaded to 180 Amps AT 16 VDC Scope Settings Volts 20.0 Control Board Replacement DescriptionControl Board Replacement ProcedureWire Drive Motor Assembly Replacement Wire Drive Motor Assembly Replacement Wire DriveBolt Gas Hose TOC Output Diode Bridge Rectifier Replacement Output Diode Bridge Rectifier Mounting Bracket Mounting Bolts Rectifier Power MIG Output Capacitors Replacement Output Capacitors Replacement Figure F.14. Capacitor Bank LocationLead Mounting Bolts Nuts & Lock washers Places Power MIG 41TROUBLESHOOTING and REPAIRF-41 Main Transformer ReplacementMain Transformer Replacement See Figure F.17Replacement Figure F.17. Leads X9, X10, 104B,104C, & H1BX2 X3 X4 X5 X6 X7 Lead Power MIG FAN BLADE/MOTOR Replacement FAN BLADE/MOTOR Replacement Perform the Output Capacitor Bank Removal ProcedureOutput Contactor Replacement Output Contactor Replacement Figure F.24Mounting Bolts Retest After Repair Electrical Diagrams Table of Contents Electrical Diagrams SectionPower MIG 200 208/230V Wiring DiagramSchematic Control PC Board PC Board ASSEMBLY-CONTROL G3851-1SVM Error Reporting Form