| TROUBLESHOOTING |
| ||||
|
|
|
|
|
|
|
| Observe all Safety Guidelines detailed throughout this manual |
|
| |||
|
|
|
|
|
| |
|
| STATUS BOARD INDICATORS |
|
| ||
|
|
|
|
|
|
|
| SYMPTOM |
|
| CHECK |
|
|
|
|
|
| |||
When trigger is pulled Red output LED is | 1. | Make sure there is at least 80 psi connected to the gas connec- |
| |||
Blinking or steady with no air flow. |
|
| tion at the back of the machine. |
|
| |
|
|
| 2. | Turn the output knob to the purge zone and set the regulator to |
| |
|
|
|
| the correct pressure. The pressure may increase when air stops |
| |
|
|
|
| flowing but this is normal. Do not reset the pressure while the air |
| |
|
|
|
| is OFF. |
|
|
|
|
| 3. | Possible faulty Pressure Switch. |
|
|
|
|
| 4. | Possible faulty Inverter board. |
|
|
|
|
|
| |||
The Green, Red and Yellow LED’s are lit | 1. | Turn the power OFF and then ON. If torch and consumables are |
| |||
and steady. Indicates safety circuit is open. |
| properly installed and they are the correct parts, the Red and |
| |||
|
|
|
| Yellow LED’s should turn off. Normal cutting or gouging can |
| |
|
|
|
| resume. |
|
|
|
|
|
|
| ||
The Thermal LED is lit. |
| 1. | The machine's thermostat has tripped due to exceeded duty |
| ||
|
|
|
| cycle limits. Do NOT turn the power off. Allow the machine to |
| |
|
|
|
| cool for 15 - 30 minutes and the thermostat will reset itself. |
|
|
|
|
| 2. | The machine's air louvers or fans are obstructed such that air |
| |
|
|
|
| cannot flow to properly cool the machine. Remove any foreign |
| |
|
|
|
| material that may block air flow. Blow the machine out with a |
| |
|
|
|
| clean, dry air stream. |
|
|
|
|
| 3. | The input voltage is not within ±10% of rated values. |
|
|
|
|
| 4. | Possible faulty Inverter board. |
|
|
|
|
|
| |||
When the trigger is pulled the Red and | 1. | Check that nozzle and swirl ring are properly installed and they |
| |||
Yellow LED’s are blinking together and the |
| are the correct parts. Note: Swirl ring can only go in one way. |
| |||
Green light is on. |
|
|
|
|
| |
|
|
| 2. | Input voltage is too low and /or air pressure is set too high. |
| |
|
|
|
| Lower air pressure. |
|
|
|
|
|
|
| ||
When the trigger is pulled the Red LED is lit, | 1. | Check that swirl ring is properly installed. |
|
| ||
air flows and no pilot arc occurs. |
|
| Note: Swirl ring can only go in one way. |
|
| |
|
|
|
| |||
The Red and Yellow LED’s are blinking | 1. | The torch safety circuit has been opened, when reconnected this |
| |||
alternately. |
|
| condition should correctly reset automatically. |
|
| |
|
|
|
|
| ||
When the trigger is pulled no air flows, Red | 1. | Check that the pressure gauge shows pressure. |
|
| ||
LED is lit, no pilot arc. Then LED goes out. |
| Air supply may not be connected or properly installed. |
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
TOMAHAWK™ 625