Lincoln Electric IM836-B manual Connection of Ranger 305D to Premises Wiring

Page 15

A-7

INSTALLATION

A-7

CONNECTION OF RANGER 305D TO PREMISES WIRING

240Volt

60 Hz.

3-Wire

Service

240 VOLT

POWER

120 VOLT

COMPANY

120 VOLT

METER

GROUNDED CONDUCTOR

NEUTRAL

BUS

DOUBLE POLE DOUBLE THROW

SWITCH RATING TO BE THE SAME

AS OR GREATER THAN PREMISES

SERVICE OVERCURRENT

PROTECTION.

			50AMP
			240 VOLT
			DOUBLE
	50 AMP, 120/240		POLE
	50 AMP, 120/240		CIRCUIT
	VOLT PLUG	240 VOLT	CIRCUIT
	VOLT PLUG	240 VOLT	BREAKER
	NEMA TYPE 14-50

GND

N

N

LOAD

PREMISES

DISCONNECT AND

SERVICE

GROUNDOVERCURRENT PROTECTION

50 AMP, 120/240 VOLT

RECEPTACLENOTE: No. 6 COPPER CONDUCTOR CABLE SEE NATIONAL ELECTRICAL CODE FOR ALTERNATE WIRE

SIZE RECOMMENDATIONS.

WARNING

•Only a licensed, certified, trained electrician should install the machine to a premises or residential electrical system. Be certain that:

•The installation complies with the National Electrical Code and all other applicable electrical codes.

•The premises is isolated and no feedback into the utility system can occur. Certain state and local laws require the premises to be isolated before the generator is linked to the premises. Check your state and local requirements.

•A double pole, double throw transfer switch in conjunction with the properly rated double throw circuit breaker is connected between the generator power and the utility meter.

RANGER 305D

Image 15

Contents Ranger 305D California Proposition 65 Warnings SafetyElectric Shock can kill Iii Welding and Cutting Sparks can Cause fire or explosionSûreté Pour Soudage a LʼArc Précautions DE SûretéThank You Table of Contents P492 Section DSection E Section FLubrication Emissions Fuel System Governor InstallationHeight Width Depth Weight AIR Cleaner Engine Idler Muffler Engine ProtectionLocation and Ventilation Safety PrecautionsOIL PRE-OPERATION Engine ServiceTowing Vehicle MountingElectrical Connections Total Combined Length of Electrode and Work Cables Cable InstallationWelding Terminals Welding Output CablesStandby Power Connections Auxiliary Power ReceptaclesConnection of Ranger 305D to Premises Wiring Control Cable Model Connection of Lincoln Electric Wire FeedersConnection of LN-15 to the Ranger 305D Across The-Arc ModelConnection of Prince XL Spool GUN to the Ranger 305D Terminals onGeneral Description OperationFigure B.1 Weld Mode Selector SwitchWire Feeder Voltmeter Switch Glow Plug Push ButtonStart Push Button Typical Ranger 305D Fuel Consumption Starting the EngineStopping the Engine Welder OperationTable B.2 TIG WeldingTypical Current Ranges 1 for Tungsten ELECTRODES2 Downhill Pipe WeldingARC Gouging Wire WELDING-CVRanger 305D Extension Cord Length Recommendations Auxiliary PowerField Installed Options / Accessories AccessoriesMaintenance Engine Maintenance Components Kubota D722 Diesel EngineKubota D722 Diesel Engine Oil Filter Change AIR CleanerEngine Oil Refill capacities Without oil filter replacement Engine Oil Change3MAINTENANCED-3 Service Instructions & Installation TipsFor Code Cooling SystemTightening the FAN Belt Bleeding the Fuel SystemArrestor Engine AdjustmentBattery Maintenance Servicing Optional SparkGfci Receptacle Testing and RESET- Ting Procedure Welder / Generator MaintenanceHOW to USE Troubleshooting Guide TroubleshootingAuthorized Field Service Facility LincolnContact your local Lincoln Welding without a control cable Functioning properly / linkage Faulty control cable. Repair or Your local Lincoln Authorized Field Service FacilityDiagrams Diagrams Diagrams Diagrams Diagrams Engine Welders LN/-8CONNECTION Diagram Diagrams Diagrams Diagrams Diagrams Enhanced For Codes 11188 M20334 Dimension PrintRanger 305D Precaucion Warnung