Lincoln Electric 575 manual Connection of the LN-25 to the Vantage

Page 18

A-8

INSTALLATION

A-8

CONNECTION OF THE LN-25 TO THE VANTAGE

The LN-25 with or without an internal contactor may be used with the Vantage. See the appropriate connection diagram in the DIAGRAMS section.

NOTE: The LN-25 (K431) Remote Control Module and (K432) Remote Cable are not recommended for use with the Vantage.

Shut the welder off.

For electrode Positive, connect the electrode cable from the LN- 25 to the “+” terminal of the welder and work cable to the “-” terminal of the welder. For electrode Negative, connect the electrode cable from the LN-25 to the “-” terminal of the welder and work cable to the “+” terminal of the welder.

Attach the single lead from the front of the LN-25 to work using the spring clip at the end of the lead. This is a sense lead to supply current to the wire feeder motor; it does not carry welding current.

Set the SELECTOR switch to the “CV-WIRE” position.

Set the “WELDING TERMINALS” switch to “WELD

TERMINALS ON”

Adjust the “ARC CONTROL” knob to desired crispness. Generally, welding is best if the “ARC CONTROL” is set to SOFT for MIG and CRISP for INNERSHIELD. You may however, want to start in the middle and adjust (as needed) from there.

Set the “IDLE” switch to the “AUTO” position. When not welding, the Vantage engine will be at the low idle speed. If you are using an LN-25 with an internal contactor, the electrode is not energized until the gun trigger is closed.

WARNING

If you are using an LN-25 without an internal contactor, the electrode will be energized when the Vantage is started.

--------------------------------------------------------------------------------------

When the gun trigger is closed, the current sensing circuit will cause the wire to begin to feed and the welding process is started.

CONNECTION OF AN NA-3 AUTOMATIC WELDING SYSTEM TO THE VANTAGE

For connection diagrams and instructions for connecting an NA-3 Welding System to the Vantage, refer to the NA-3 Welding System instruction manual. The connection diagram for the LN-8 can be used for connecting the NA-3.

• Set the Wire Feeder Voltage Switch to 115V.

CONNECTION OF PRINCE XL SPOOL GUN TO THE VANTAGE

Connection of the Prince XL Spool Gun requires the use of the K1849-1 Adapter Module.

Shut the Welder off.

For electrode Positive, connect the electrode cable to the "+" terminal of the welder and work cable to the "-" terminal of the welder. For electrode Negative, connect the electrode cable "- " terminal of the welder and work cable to the "+" terminal of the welder.

Connect the Control Cable of the Spool Gun to the Adapter Module and connect the Control Cable of the Adapter Module to the Welder.

Connect the Gas Hose.

Set the MODE switch to the "CV-WIRE " position.

Set the WIRE FEEDER VOLTAGE switch to 42 volts.

Set the "WELD TERMINALS" switch to "WELD TERMINALS ON".

Set the "ARC CONTROL" knob to "0" initially and adjust to suit.

Set the "IDLE" switch to the "High" position

Vantage 575

Image 18
Contents Vantage Safety Electric Shock can kill For Electrically powered equipment Safety Précautions DE SûretéWELDING, EMF & Pacemakers Instructions for Electromagnetic Compatibility Thank You Table of Contents Accessories Section C Installation Installation Safety PrecautionsLocation / Ventilation High Altitude Operation High Temperature OperationLifting TowingPRE-OPERATION Engine Service Welding Terminals Standby Power Connections Remote ControlAuxiliary Power Receptacles OutputConnection of Lincoln Electric Wire Feeders Connection of the LN-25 to the Vantage Connection of Prince XL Spool GUN to the VantageGeneral Description Safety InstructionsOperation Recommended ApplicationsStart Pushbutton RUN Stop SwitchEngine Temperature Gauge Hour MeterOIL Pressure Gauge Battery Charging LightIdler Switch Engine ProtectionAuxiliary Power Controls Engine Operation Starting the EngineStopping the Engine BREAK-IN Period Operation For Tungsten ElectrodesAuxiliary Power Operation Table B.4 Vantage Simultaneous Welding and Power Loads Accessories Optional Field Installed AccessoriesMaintenance Routine and Periodic MaintenanceEngine Maintenance Battery Handling Fuel FiltersCooling System Welder / Generator Maintenance Troubleshooting HOW to USE Troubleshooting GuideTroubleshooting Troubleshooting Problems Possible Areas Recommended Misadjustments Course of ActionDiagrams Vantage 575 Wiring Diagram K2170-1 50HZDIAGRAMSF-2 Commander / K867 / K775 / LN-7 Connection Diagram Diagrams Diagrams Commander / K867 / LN-8 Connection Diagram Diagrams Diagrams Engine Welders /LN-8 Connection Diagram Diagrams Diagrams Diagrams Diagrams Dimension Print Vantage Vantage Aviso DE Precaucion