Lincoln Electric 5000 manual Stacking, Tilting, Lifting

Page 10

A-3	INSTALLATION	A-3

STACKING

POWER ARC 5000 machines CANNOT be stacked.

TILTING

Place the machine on a secure, level surface whenev- er you use it or store it. Any surfaces you place it on other than the ground must be firm, non-skid, and structurally sound.

The gasoline engine is designed to run in a level posi- tion for best performance. It can operate at an angle, but this should never be more than 15 degrees in any direction. If you do operate it at a slight angle, be sure to check the oil regularly and keep the oil level full. Also, fuel capacity will be a little less at an angle.

ASSEMBLY OF VIBRATION ISOLATORS TO BOTTOM OF TUBE FRAME ( If wheels are not used)

Tools required - 9/16 wrench or socket.

If the supplied wheels are not used, it is important that the isolators are installed to keep the machine stabilized when operated on a smooth surface.

Install the four molded rubber vibration isolators to the bot- tom of the engine and alternator support channels using four each of the supplied 3/8-16 X .875 hex head screws, lock- washers, and large plain washers (spacers). The large plain washers (spacers) must be installed between the isolator and the underside of the channels. See Figure A-1.

LIFTING

The POWER ARC 5000 should be lifted by four peo- ple. (It weighs 208 lbs/94.3 kg.) Its welded tube roll cage is designed to make lifting easy.

Figure A-1

3/8-16 x .875 Hex Head Bolt

Lockwasher

Frame

Large Plain Washer (Spacer) Rubber Isolator

POWER ARC 5000

Image 10

Contents Power ARC Safety Depends on YouSafety California Proposition 65 WarningsElectric Shock can kill Welding Sparks can cause fire or explosion IiiPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcThank You Please Examine Carton and Equipment For Damage ImmediatelyTable of Contents Installation Technical Specifications Power ARCLocation and Ventilation Safety PrecautionsStoring Tilting StackingLifting Assembly of Wheels and Handle to the Tube Frame Fuel PRE-OPERATION Engine ServiceOIL Spark ArresterElectrical Output Connections Welding Cable ConnectionsCable Installation Auxiliary Power ReceptaclesMachine Grounding Plugs and HAND-HELD Equipment Power Cord Connections to TWIST- Lock PlugsPremises Wiring Circuit BreakersThese Devices Without Operating Instructions Safety InstructionsOperation General DescriptionWelding Capability Recommended ApplicationsLimitations Controls and Settings GENERATOR/WELDER ControlsFigure B.2 Gasoline Engine Controls Gasoline Engine ControlsBefore Starting the Engine Engine OperationStarting the Engine For a HOT Engine Stopping the EngineBREAK-IN Period For Best Engine StartingGenerator Operation To USE the Generator AS AN Auxiliary Power SupplyGeneral Information Table B.3 Generator Power Applications Suggested Power Applications Running Watts Start-up WattsControl Function / Operation Current Control Dial To USE the Power ARC 5000 for Stick WeldingWelding Operation After YOU Finish the WeldWelding Guidelines Stick Welding What Happens in the Arc? Figure B.4 The welding arcCorrect Way to Strike An Arc Correct Welding Position Correct Arc LengthCorrect Welding Speed Common Metals PracticeTypes of Welds Multiple Pass Welds PenetrationFillet Welds Welding in the Vertical PositionVertical-Up Welding Vertical-Down WeldingWelding Sheet Metal How to Hardface the Sharp Edge Metal to Ground WearOverhead Welding Hardfacing To Reduce WearWelding Cast Iron Cast Iron Plate PreparationHigh-Speed Group AWS E6013 Selecting ElectrodesOut-of-Position Group AWS E6011 Low Hydrogen Group Stable-Arc E7018Lincoln Electric Accessories AccessoriesOPTIONS/ACCESSORIES Briggs and Stratton AccessoriesEngine Maintenance MaintenanceRoutine and Periodic Maintenance Engine AdjustmentsFigure D.3 Clean Cooling System Clean AIR Filter PRE-CLEANERTable D.2 Engine Maintenance Parts Part Part NumberGENERATOR/WELDER Maintenance Figure D.6. Brush Removal and ReplacementFigure D.7. Major Component Locations Symptoms TroubleshootingPossible Areas Generator POWER, Always Not RUN Engine Without AN Diagrams Wiring Diagram Power ARCDimension Print Need Welding Training? How To Read Shop DrawingsNew Lessons in Arc Welding Basic CoursePrecaucion Warnung