Lincoln Electric 5000 manual Options/Accessories, Lincoln Electric Accessories

Page 36

C-1	ACCESSORIES	C-1

OPTIONS/ACCESSORIES

LINCOLN ELECTRIC ACCESSORIES

The following options/accessories are available for your POWER ARC 5000 from your local Lincoln Distributor.

Accessory Set (K875) – Includes the following:

•Twenty feet (6.1 meters) of #6 AWG electrode cable

•Fifteen feet (4.6 meters) of #6 work cable

•Headshield with No. 10 filter

•Work clamp

•Insulated electrode holder

•Sample electrodes

The cables are rated at 150 amps, 40% duty cycle.

Spark Arrester (K883-2)– A field-installed kit for the 11 HP Briggs & Stratton engine.

Rotor Removal Kit (S20925) – A service kit for removing the generator rotor from the tapered engine crankshaft.

BRIGGS AND STRATTON ACCESSORIES

The following options/accessories are available for your POWER ARC 5000 from your local Briggs & Stratton Distributor.

Exhaust Deflector (B&S No.393761) - Used to deflect engine exhaust down. Attaches to the muffler with four screws.

POWER ARC 5000

Image 36

Contents Power ARC Safety Depends on YouSafety California Proposition 65 WarningsElectric Shock can kill Welding Sparks can cause fire or explosion IiiPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcThank You Please Examine Carton and Equipment For Damage ImmediatelyTable of Contents Installation Technical Specifications Power ARCSafety Precautions Location and VentilationStoring Stacking TiltingLifting Assembly of Wheels and Handle to the Tube Frame PRE-OPERATION Engine Service OILFuel Spark ArresterElectrical Output Connections Welding Cable ConnectionsAuxiliary Power Receptacles Cable InstallationMachine Grounding Power Cord Connections to TWIST- Lock Plugs Premises WiringPlugs and HAND-HELD Equipment Circuit BreakersThese Devices Without Safety Instructions OperationOperating Instructions General DescriptionRecommended Applications Welding CapabilityLimitations Controls and Settings GENERATOR/WELDER ControlsFigure B.2 Gasoline Engine Controls Gasoline Engine ControlsEngine Operation Before Starting the EngineStarting the Engine Stopping the Engine BREAK-IN PeriodFor a HOT Engine For Best Engine StartingTo USE the Generator AS AN Auxiliary Power Supply Generator OperationGeneral Information Table B.3 Generator Power Applications Suggested Power Applications Running Watts Start-up WattsTo USE the Power ARC 5000 for Stick Welding Welding OperationControl Function / Operation Current Control Dial After YOU Finish the WeldWelding Guidelines Stick Welding What Happens in the Arc? Figure B.4 The welding arcCorrect Welding Position Correct Arc Length Correct Way to Strike An ArcCorrect Welding Speed Practice Common MetalsTypes of Welds Penetration Fillet WeldsMultiple Pass Welds Welding in the Vertical PositionVertical-Up Welding Vertical-Down WeldingHow to Hardface the Sharp Edge Metal to Ground Wear Overhead WeldingWelding Sheet Metal Hardfacing To Reduce WearWelding Cast Iron Cast Iron Plate PreparationSelecting Electrodes Out-of-Position Group AWS E6011High-Speed Group AWS E6013 Low Hydrogen Group Stable-Arc E7018Accessories OPTIONS/ACCESSORIESLincoln Electric Accessories Briggs and Stratton AccessoriesMaintenance Routine and Periodic MaintenanceEngine Maintenance Engine AdjustmentsFigure D.3 Clean Cooling System Clean AIR Filter PRE-CLEANERTable D.2 Engine Maintenance Parts Part Part NumberGENERATOR/WELDER Maintenance Figure D.6. Brush Removal and ReplacementFigure D.7. Major Component Locations Troubleshooting SymptomsPossible Areas Generator POWER, Always Not RUN Engine Without AN Diagrams Wiring Diagram Power ARCDimension Print How To Read Shop Drawings New Lessons in Arc WeldingNeed Welding Training? Basic CoursePrecaucion Warnung