Kawasaki 840108 Charging Battery Pack, Remove Battery Pack 1. Press both release

Page 26

REMOVING / ATTACHING BATTERY PACK

REMOVE BATTERY PACK: 1. Press both release

buttons on either side of the Cordless Reciprocating Saw to release the battery pack.

2. Pull battery pack free of Cordless Reciprocating Saw.

The battery pack and charger heat during charging. Place the charger on a flat, non-flammable surface away from flammable materials with at least four inches of clearance to allow proper air circulation around the charger and battery pack.

When the battery pack requires recharging, a 3-5 hour charge allows the tool to operate at full power. A charging indicator light on the charger will illuminate to show that charging is taking place.

CHARGING BATTERY PACK

ATTACH BATTERY PACK:

1. Align the raised portion of the battery pack with the groove in the battery compartment

CHARGE BATTERY PACK:

1. Make sure the trigger on

the Cordless Reciprocating

Saw is in the “OFF”

position and remove

BATTERY PACK

of the Cordless Reciprocating Saw.

RELEASE BUTTON

the battery pack

from the Cordless

120V AC

ADAPTER

2.Press the battery pack into place. Make sure the latches are securely fastened. Do not use the Cordless Reciprocating Saw if the battery pack is not seated properly.

CHARGER

Before using battery charger, please read carefully all instructions and cautionary markings on battery charger, battery pack and product using battery.

Reciprocating Saw.

2. Plug 120V AC Adapter into

household outlet and into

side of battery charger.

Insert battery pack into

battery charger. LED light

will turn green when

battery pack is fully

charged (approx. 3 hours).

LED LIGHT

BATTERY

CHARGER

The charger will not automatically turn “OFF” when the battery pack is fully charged. The charging indicator light will remain “ON” until the charger is disconnected from the electrical outlet.

Use only the charger which accompanied your product or direct replacement as listed in this manual. Do not substitute any other charger. Use only Alltrade approved chargers with your product.

Do not disassemble charger.

Do not use charger if it has been damaged, left outdoors in the rain, snow, wet or damp environments, or immersed in liquid.

3.When fully charged, reattach battery pack onto Cordless Reciprocating Saw, making certain latches fasten securely. Cordless Reciprocating Saw will not operate properly if the battery pack is not seated properly.

9

10

Image 26 Contents
Manual DE Instrucciones Para EL Taladro Inalámbrico DE Recognize Safety SYMBOLS, Words and Labels Table of ContentsGeneral Safety Rules for ALL Battery Operated Tools CongratulationsPersonal Safety Important SafeguardsElectrical Safety Save These Instructions for Future ReferenceSafety Rules for Cordless Drill / Drivers ServiceSpecific Safety Rules AND/OR Symbols Tool USE and CareFunctional Description SymbolsSymbol Name Explanation Component Model NumberRemove Battery Pack BatteryRemoving / Attaching Battery Pack Attach Battery PackVariable Speed Trigger Switch Charging Battery PackAssembly Installing Drive BIT Into Keyless ChuckScrew Driving Torque SettingsForward / Reverse and Trigger Lock Lever Drilling MetalHints for Optimum USE Maintenance and CleaningAccessories Conductor Size in A.W.GProtecting the Environment SpecificationsYear Limited Home USE Warranty Other Consumer DO-IT-YOURSELF DIY ToolsExclusions Component #840108 Congratulations Table of ContentsRecognize Safety SYMBOLS, Words and Labels Intended USEBattery Important SafeguardsSafety Rules for Worklight Removing / Attaching Battery Pack ChargerSymbol Name Explanation Charging Battery Pack Symbol Name ExplanationSymbols Operating InstructionsReplacing the Light Bulb Adjusting the Worklight BeamMaintenance and Cleaning Service AccessoriesSpecifications Protecting the EnvironmentYear Limited Home USE Warranty Warranty PerformanceWarranty Disclaimers Component #840108 General Safety Rules for ALL Battery Operated Tools Work Area Electrical SafetyPersonal Safety Safety Rules for Cordless Reciprocating SAW Tool USE and CareSpecific Safety Rules AND/OR Symbols Charging Battery Pack Remove Battery Pack 1. Press both release120V AC Adapter Variable Speed Trigger Switch Attaching / Removing BladeGeneral Cutting Plunge CuttingMetal Cutting Battery Type Ni-Cad Year Limited Home USE Warranty Warranty Disclaimers 18V Battery Pack Congratulations Symbols Year Limited Home USE Warranty Warranty Disclaimers
Related manuals
Manual 38 pages 30.93 Kb