Xantrex Technology 10, 15, 30, 20 owner manual Installation Option 4 for Freedom Marine 25

Page 35

INSTALLATION OPTIONS

Installation Option 4 for Freedom Marine 25 and 30

The inverter is used in a Dual Input/Dual Output mode. The AC loads are split between main loads and inverter loads. The external sources of AC power can be two different 30 amp shorepower sources (both neutrals and both “Hots” must be kept separate), or two 30 amp breakers from a panel fed by a 50 amp 120 volt single phase (3 wire) shorepower source, a 50 amp 120/240 volt split phase (4 wire) shorepower source, or a generator. The charger uses one 30 amp source of power (AC Input #1) and the other 30 amp source (AC Input #2) transfers through the inverter to the inverter loads connected to AC Output #2. In inverter mode, the inverter powers both groups of inverter loads. In charge/transfer mode, up to 60 amps can be transferred to the inverter loads. The inverter loads are split into two groups so that these loads can be used to help balance the two legs of shorepower or generator power.

It is highly recommended that only the lighter appliances and outlet circuits be connected to the Inverter AC Panel. These loads are supplied power through the inverter in charge/transfer mode, or by the inverter in invert mode. The heavier loads such as space heaters, stoves, water heaters, air conditioners, AC to DC converters, or other battery chargers should remain connected to the Main AC Panel. These loads are only supplied by shorepower or generator power from the main panel. This split load approach will help avoid problems such as overloading the inverter or rapidly discharging the battery bank, and eliminates the need to manually manage the energy usage of these loads when using inverter power.

The inverter AC Input #1 must be supplied power from a 30 amp breaker and neutral in the main panel and is used to power the charger and transfer up to 30 amps through to the inverter loads connected to AC Output #1. AC Input #2 must be supplied by a second 30 amp breaker in the main panel which transfers through the inverter to AC Output #2. These two input breakers can be supplied by the same phase or by opposite phases. The inverter AC outputs supply a separate sub panel. The appliance and outlet loads are then supplied with power from the inverter hot and inverter neutral buses in the sub panel.

If a generator is installed in the system, a break-before-make AC transfer switch is used to select between shorepower or generator power. The transfer switch AC output is then routed to the input of the Main AC Panel.

If only AC Input #1 is supplied power, the unit will charge and transfer up to 30 amps through to both groups of inverter loads. The charger will power share with both groups of inverter loads.

If only AC Input #2 is supplied power, the unit will not charge, and will only transfer 30 amps through to the inverter loads connected to AC Output #2 only.

35

Image 35
Contents Page Disclaimer Safety SummaryTable of Contents Freedom Amps DC Freedom WattsIntroduction Inverter Idle Circuit Power SharingCircuit Breaker Protection Electronic Protection Temperature Sensitive Charging TSCOperation Invert ModeCharge Mode OVER-TEMP/OVERLOAD Red LED LOW Battery Red LEDLOW Battery & OVER-TEMP/OVERLOAD Battery Type SelectionOptional Remotes TSC Temperature Sensitive ChargingLink Optional Remote Control PanelsRemote Control Panel Advanced Remote Control Panels Link InstrumentsWet Cell Batteries Battery TypesBatteries Battery InterconnectionParallel Parallel ConfigurationBattery Bank Ratings and Sizing AMP-HOUR Consumption Formulas Freedom Battery Chargers Battery ChargingBattery Charging Battery charger stages are Acceptance to Float Transition Points Battery Charging Battery Charger Voltage Settings Typical Tools Needed Installation PrecautionsAccessories Needed for Installation Confirm that your shipping carton containsKey Installation Points Installation+ Positive Negative Neutral Bonding GroundingBlack to Black AC WiringGround/green White to WhiteDC Wiring InstallationGround Fault Circult Interrupters Battery Cable Connections For Freedom 10 Battery Cable FusingInverter/charger configurations Installation OptionsInstallation Options Dual In/Dual Out Configuration Installation Option 1 for Freedom Marine 10, 15, 20, 25, Freedom Marine Installation OptionFreedom Marine Model 10, 15, 20, 25 Installation Option 2 for Freedom Marine 10, 15, 20, 25,Installation Option 3 for Freedom Marine 25 Freedom Marine Installation Option Installation Option 4 for Freedom Marine 25 Dual Input/ Dual Output Test the transfer function Installation ChecksTest the battery charger function Troubleshooting LED Status Voltage TroubleshootingGlossary LED Light Emitting Diode Indicator light Specifications What does this warranty cover? WarrantyProduct Return Procedure Page Xantrex Technology Inc
Related manuals
Manual 68 pages 34.63 Kb