Xantrex Technology 10, 15, 30, 20, 25 owner manual Troubleshooting, Voltage

Page 40

TROUBLESHOOTING

Problem

Things to Check

 

 

 

1. Battery voltage under load below 10 volts. Charge batteries.

 

2. Loose battery connections, open battery switch or blown DC fuse.

 

Tighten connections or replace fuse.

 

3. Tripped circuit breaker on front panel. Push-in to reset breaker.

No Inverter Output

4. Thermal condition, excessive loads or inadequate ventilation

 

caused overheating. Allow to cool. Ventilate the compartment.

 

5. Overloads or short circuit, check for excessive loads or shorted

 

wiring. Disconnect loads.

 

 

 

Confirm that your volt meter is a True RMS meter. Standard volt

Low Inverter

meters will not accurately read the waveform of the inverter and may

read anywhere from 90 to 120 volts. If a True RMS meter is not

Output Voltage

available, check the brightness of an incandescent light bulb - if it

 

 

appears normal, the output voltage is properly regulated.

 

 

 

1. Wiring - check both the AC and DC connections.

 

2. AC input voltage - low voltage input will result in low DC output

 

current. Expect reduced charger output from generators under 3,500

 

watts.

 

3. Check power share setting if using a remote panel.

Little or No Output

4. If Starter or Auxiliary battery is not charging quickly, check the

difference between the house battery and the starter battery with a

from Battery

volt meter. If difference is greater than 3.2 volts, the echo~charge will

Chargers

reduce energy delivered to the start battery. Check all connections to

 

 

the house and starter battery.

 

5. If there is no energy output to the start battery and the house

 

battery voltage is above 13.0 volts, a thermal shutdown of the

 

individual echo~charge has occured. The echo~charge will

 

automatically restart when the temperature drops to a safe level.

 

 

 

1. Microwave ovens will normally cook slower on inverter power

 

because the modified sine wave output has a slightly low peak AC

Microwave Oven

voltage.

Cooking Slow

2. Cooking speed will be determined by battery voltage. Low voltage

 

results in increased cooking time. Support the battery bank with an

 

alternator or other charging source for quicker cooking.

 

 

 

1. Digital clocks either employ an internal time base or derive their

 

time base from the incoming AC waveform. The inverter frequency is

Slow or Fast

well regulated at 60 Hz. The clock either counts the number of peaks

in the waveform or the number of times the waveform crosses zero

Digital Clock

volts. The circuitry that counts the zero crossing events is more

 

 

popular. The longer zero cross time of the inverter's modified sine

 

wave may cause double clocking, resulting in a faster clock.

 

 

40

Image 40
Contents Page Safety Summary DisclaimerTable of Contents Freedom Watts Freedom Amps DCIntroduction Circuit Breaker Protection Power SharingInverter Idle Circuit Temperature Sensitive Charging TSC Electronic ProtectionCharge Mode Invert ModeOperation LOW Battery Red LED LOW Battery & OVER-TEMP/OVERLOADBattery Type Selection OVER-TEMP/OVERLOAD Red LEDTSC Temperature Sensitive Charging Optional RemotesOptional Remote Control Panels Remote Control PanelAdvanced Remote Control Panels Link Instruments LinkBattery Types Wet Cell BatteriesBattery Interconnection BatteriesBattery Bank Ratings and Sizing Parallel ConfigurationParallel AMP-HOUR Consumption Formulas Battery Charging Battery ChargingFreedom Battery Chargers Battery charger stages are Acceptance to Float Transition Points Battery Charging Battery Charger Voltage Settings Installation Precautions Accessories Needed for InstallationConfirm that your shipping carton contains Typical Tools NeededInstallation Key Installation Points+ Positive Negative Grounding Neutral BondingAC Wiring Ground/greenWhite to White Black to BlackGround Fault Circult Interrupters InstallationDC Wiring Battery Cable Connections Battery Cable Fusing For Freedom 10Installation Options Installation OptionsInverter/charger configurations Dual In/Dual Out Configuration Freedom Marine Installation Option Installation Option 1 for Freedom Marine 10, 15, 20, 25,Installation Option 2 for Freedom Marine 10, 15, 20, 25, Freedom Marine Model 10, 15, 20, 25Installation Option 3 for Freedom Marine 25 Freedom Marine Installation Option Installation Option 4 for Freedom Marine 25 Dual Input/ Dual Output Installation Checks Test the transfer functionTest the battery charger function Troubleshooting LED Status Troubleshooting VoltageGlossary LED Light Emitting Diode Indicator light Specifications Warranty What does this warranty cover?Product Return Procedure Page Xantrex Technology Inc
Related manuals
Manual 68 pages 34.63 Kb