Harbor Freight Tools 32208, 32206 manual To Adjust The Upper Blade Guides And Support Bearings

Page 14

4.NOTE: Adjust the Knob Bolt (7B) only a fraction at a time. Never attempt to adjust the tracking of the Saw Blade while the Bandsaw is running.

To Adjust The Upper Blade Guides And Support Bearings:

1.The Upper Blade Guides (29B) and Upper Blade Guide Support Bearing (47B) should be adjusted only after the Saw Blade tension and tracking is properly ad- justed. (See Figure T.)

2.The Upper Blade Guides (29B) are held in place by the two Thumb Bolts (72B).

3.Loosen the two Thumb Bolts (72B) to move the Upper Blade Guides (29B) as close as possible to the side of the Saw Blade, being careful not to pinch the Saw Blade. Then, securely tighten the Thumb Bolts.

4.The Upper Blade Guide Support Bearing (47B) prevents the Saw Blade from being pushed too far to the back. The Upper Blade Guide Support Bearing should be set 1/64” (0.4mm) behind the Saw Blade by loosening the Hex Head Bolt (61B) to move the Upper Blade Guide Support Bearing in or out.

5.The Upper Blade Guide Support Bearing (47B) should also be adjusted sothe back edge of the Saw Blade overlaps the outside diameter of the Blade Guide Support Bearing by about 1/16”.

To Adjust The Lower Blade Guide And Support Bearing:

1.The Lower Blade Guides (32B) and Lower Blade Guide Support Bearing (47B) should be adjusted at the same time as the Upper Blade Guides and Upper Blade Guide Support Bearing. (See Figure V.)

2.Loosen the two Thumb Bolts (72B) to move the Lower Blade Guides (32B) as close as possible to the side of the Saw Blade, being careful not to pinch the Saw Blade. Then, securely tighten the Thumb Bolts.

3.The Lower Blade Guide Support Bearing (47B) should be adjusted so it is about 1/ 64” (0.4mm) behind the back of the Saw Blade by turning the Bolt (59B).

To Adjust The Upper Blade Guide Assembly:

1.The Upper Blade Guide Assembly should always be set as close as possible to the top surface of the material being cut. To do so, loosen the Knob Bolt (25B) and raise or lower the Upper Blade Guide Assembly to the desired position. Then, securely tighten the Knob Bolt. (See Figure W.)

SKU 32208/32206 For technical questions, please call 1-800-444-3353.

PAGE 14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents For technical questions or replacement parts, please call Wood BandsawSave this Manual SpecificationsGeneral Safety Warnings and Precautions Specific Product Warnings and Precautions Industrial Applications Must Follow Osha RequirementsFigure a SKU 32208/32206 For technical questions, please call Unpacking See Figure C and Hardware DiagramSee Figure D and Hardware Diagram Operating InstructionsTo Assemble The Motor Onto The Stand See Figure F and Hardware DiagramHardware Diagram Diagram To Assemble The Bandsaw Body To The StandFigure K See Figure KFigure L 39A. See Figure N To Install The Side Panels To The StandTo Install The Saw Blade Lighted in Figure O stepSee Figures T See Figure RSee Figures T and U To Adjust The Saw Blade Tension To Adjust The Tracking Of The Saw BladeTo Adjust The Upper Blade Guide Assembly To Adjust The Upper Blade Guides And Support BearingsTo Adjust The Lower Blade Guide And Support Bearing REV 04/02 To Adjust The Angle Of The TableTo Attach The Guide Post Guard Figure Y To Attach The Dust ChuteFigure AA To Operate The BandsawTroubleshooting Guide Please Read the Following Carefully REV 03/04 Assembly Diagram aStand Assembly Diagram B Parts List Assembly B Saw Body Parts List Assembly B Saw Body Parts List Assembly C Parts List Assembly D Assembly Diagram E Assembly Diagram F Hardware Diagram Wiring Diagram
Top Page Image Contents