Porter-Cable 90546382 LED Light, Removable Shoe Sleeve Figure F, RIP / Circle Cutting Figure G, H

Page 7

90546382 PC600JS Jig Saw 12/10/08 9:11 AM Page 7

CUTTING ACTION – ORBITAL OR STRAIGHT

E

(FIGURE E)

 

 

 

 

 

 

 

:

Check that the tool is not locked ON

 

 

 

 

 

before connecting it to a power supply. If the trigger

 

switch is locked ON when the tool is connected to the

 

power supply, it will start immediately. Damage to your

 

tool or personal injury may result.

 

This jig saw is equipped with four cutting actions,

 

three orbital and one straight. Orbital action has a

 

more aggressive blade motion and is designed for

 

cutting in soft materials like wood or plastic. Orbital

 

action provides a faster cut, but with a less smooth

 

cut across the material. In orbital action, the blade

 

 

moves forward during the cutting stroke in addition to the up and down motion. NOTE: Metal or hardwoods should never be cut in orbital action.

To adjust the cutting action:

-Move the cutting action lever (9) between the four cutting positions: 0, 1, 2, and 3.

-Position 0 is straight cutting.

-Positions 1, 2, and 3 are orbital cutting.

-The aggressiveness of the cut increases as the lever is adjusted from one to three, with three being the most aggressive cut.

LED LIGHT

The jig saw is equipped with a light which projects on the cutting path.

-The light will come on when the trigger switch is depressed and will go off when the trigger switch is released.

REMOVABLE SHOE SLEEVE (FIGURE F)

The non-marring shoe sleeve (5) should be used when cutting surfaces that scratch easily, such as laminate, veneer, or paint. It can also be used to protect the shoe surface during transportation and storage.

To attach shoe sleeve, place the front of the shoe

(6)into the front of the shoe sleeve (5) and lower the jig saw as shown in figure F. The shoe sleeve will click securely onto the rear of the shoe.

To remove shoe sleeve, grasp the sleeve from the bottom at the two rear tabs and pull down and away from the shoe.

F

Hints for optimum use

Sawing laminates

As the saw blade cuts on the upward stroke, splintering may occur on the surface closest to the shoe plate.

-Use a fine-tooth saw blade.

-Saw from the back surface of the workpiece.

-To minimize splintering, clamp a piece of scrap wood or hardboard to both sides of the workpiece and saw through this sandwich.

Sawing metal

-Be aware that sawing metal takes much more time than sawing wood.

-Use a saw blade suitable for sawing metal.

-When cutting thin metal, clamp a piece of scrap wood to the back surface of the workpiece and cut through this sandwich.

-Spread a film of oil along the intended line of cut for easier operation and longer blade life. For cutting aluminum, kerosene is preferred.

RIP / CIRCLE CUTTING (FIGURE G, H)

Ripping and circle cutting without a pencil line are easily done with the rip fence / circle guide (not included - available at extra cost).

Using the screw supplied with the accessory guide, position as shown in figure G and

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Catalog Number PC600JS Advertencia Léase EsteWork area safety General Safety RulesSpecific Safety Rules Safety Guidelines Definitions Functional Description SymbolsOperation Blade Installation Figure BAdjusting the Shoe for Bevel Cuts Figure C Switching on and OFFRemovable Shoe Sleeve Figure F LED LightRIP / Circle Cutting Figure G, H Problem Possible Cause TroubleshootingPossible Solution Accessories Three Year Limited WarrantyMaintenance Replacement Parts Service and Repairs90546382 PC600JS Jig Saw 12/10/08 911 AM DE Catalogue PC600JS Manuel dinstructionsConserver CES Directives Avertissements de sécurité généraux90546382 PC600JS Jig Saw 12/10/08 911 AM Consignes DE Sécurité Particulières Lignes Directrices EN Matière DE Sécurité Définitions SymbolesRéglage DE LA Semelle Pour DES Coupes Biseautées Figure C Installation DE LA Lame Figure BFonctionnement Description FonctionnelleMise EN Marche ET Arrêt Commande DE LA Vitesse VariablePour régler le mode de coupe Pour régler la semelle pour des coupes droitesCoupe du métal Manchon DE Semelle Amovible Figure FPour retirer le manchon de semelle, saisir le bas du Coupe de lamellésPièces DE Rechange Problème Cause possible Solution possibleDépannage EntretienEntretien ET Réparation AccessoiresRemplacement DES Étiquettes D’AVERTISSEMENT Garantie Limitée DE Trois ANSHighway 45 North Jackson, Tennessee 888 Catálogo N PC600JS Manual deinstruccionesConserve Estas Instrucciones Advertencias generales de seguridadEsto garantizará la seguridad de la herramienta eléctrica Normas Específicas DE Seguridad Símbolos Pautas DE SEGURIDAD/DEFINICIONESAjuste DE LA Zapata Para Cortes EN Bisel Figura C OperaciónDescripción DE LAS Funciones Instalación DE LA Hoja Figura BAcción DE Corte Orbital O EN Línea Recta Figura E Para fijar la zapata para cortes rectosEncendido Y Apagado Control DE Velocidad Variable Figura DCortes Longitudinales Y Cortes DE Círculos Figura G, H Retire LA Manga DE LA Zapata Figura FPara aserrar laminados Aserrado en metalPiezas DE Repuesto Detección DE ProblemasProblema Causa posible Solución posible MantenimientoReemplazo DE LAS Etiquetas DE Advertencia Garantía Limitada DE Tres AñosMantenimiento Y Reparaciones AccesoriosCatalog Numbers PC600JS EspecificacionesDEC. ‘08

90546382, PC600JS specifications

The Porter-Cable PC600JS is a highly regarded jigsaw designed for both professional craftsmen and DIY enthusiasts. This powerful tool provides versatility and precision, making it a staple in woodworking and various cutting applications.

At the heart of the PC600JS is its robust 6-amp motor, which delivers impressive power for cutting through a diverse range of materials including wood, metal, and plastic. The variable speed control allows users to adjust the speed from 0 to 3,000 strokes per minute, catering to a variety of cutting tasks. This flexibility helps ensure clean, accurate cuts across different material types.

One of the standout features of the Porter-Cable PC600JS is its four-position orbital action. This technology enhances the jigsaw's cutting efficiency, allowing users to choose the best cutting style for their specific project. Depending on the application, the user can opt for a faster, more aggressive cut or a slower, finer approach. This adaptability makes the PC600JS suitable for everything from intricate curves to straight cuts.

The tool is designed with user comfort in mind. Its lightweight design reduces hand fatigue during extended use, while the soft-grip handle provides a secure and comfortable hold. Additionally, the integrated dust blower keeps the cutting line clear of debris, allowing for improved visibility and accuracy during operation.

The PC600JS is also equipped with a tool-free blade change mechanism, which saves time and effort. This feature allows users to quickly swap out blades without the need for additional tools, making transitions between different tasks seamless and efficient.

Another notable characteristic is the included bevel plate, which permits a 0 to 45-degree angle for bevel cuts. This feature extends the versatility of the jigsaw, allowing users to create angled cuts for various woodworking projects. The clear base design also provides better sight lines, enabling precise cutting.

In summary, the Porter-Cable PC600JS jigsaw is a reliable tool that combines power, versatility, and user-friendly features. With a focus on performance and comfort, it is an excellent choice for both professionals and hobbyists looking to tackle a wide range of cutting tasks with precision and ease.
Top Page Image Contents