Grizzly G0588, G0591 owner manual 220/440V 3-Phase, Wiring

Page 21

220/440V 3-Phase

Serious personal injury could occur if you connect your machine to the power source before you have completed the set up pro- cess. DO NOT connect the machine to the power source until instructed to do so.

Wiring

The Model G0588 is prewired for 220V 3-phase operation. If 440 voltage is required, rewire the machine according to the instructions on Page 14 and follow the circuit requirements on this page.

Amperage Draw

The Model G0588 has a 71⁄2 HP main motor that will draw the following amps:

Motor Draw at 220V	20 Amps
Motor Draw at 440V	10 Amps

Minimum Circuit Requirements

Only connect your machine to a circuit that meets the requirements below. Check to see if the wires and circuit breaker in your circuit are capable of handling the amperage draw from your machine, as well as any other machines that could be operating on the same circuit. If you are unsure, consult a qualified electrician.

220V Circuit	25 Amp
440V Circuit	15 Amp

Minimum Cord Requirements

Use the following type of cord to connect your machine to power (a cord is not provided):

Cord	4 wire
Gauge	10 Gauge

Connection Type

We recommend hardwiring 3-phase machines directly to the circuit breaker and installing a lock- ing shut-off lever near the machine as a way to quickly disconnect the power and prevent acci- dental starting (see Figure 5).

Figure 5. A power disconnect is preferable to

high current plugs and receptacles.

A fire may occur if your particular electrical configuration does not comply with local and state codes. The best way to ensure compli- ance is to check with your local municipality or a qualified electrician.

G0588/G0591 12" Sliding Table Saws

-13-

Image 21

Contents Sliding Table SAW Sliding Table January This page replaces page 56 of the original manual Sliding Table Parts JanuaryPage G0588/91 Crosscut Fence July Front Support Block G0588/91 Crosscut Fence JulyModel G0588/G0591 Sliding Table SAWPage Table of Contents Operations Introduction ForewordContact Info Machine Data Sheet Blade Angle Handwheel Adjusts the angle Power ON/OFF Buttons Turns the mainIdentification Emergency Stop Button TurnsPage Safety Instructions for Machinery SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Sliding Table Saws Preventing Kickback Protecting Yourself From KickbackBelow are tips to reduce the likelihood of kickback Glossary of Terms Circuit Requirements 220V Single-PhaseWiring 220/440V 3-PhaseControl panel cover plate G0588/G0591 12 Sliding Table Saws Phase Converter Rewiring to GroundingMagnetic switch Set Up Safety Unpacking SET UPItems Needed for Set Up Description QtySite Considerations Moving & Placing Base UnitCrate Qty Saw Base Unit Not Shown Clean Up InventoryHardware and Tools Blade guard components Edge Shoe Hold DownHardware Recognition Chart To install the sliding table Sliding TableComponents and Hardware Needed Qty Extension Tables To install the extension tablesRip Fence and Scale To install the rip fencePage Main Blade To install the bladeScoring Blade To install the scoring bladeAligning Blades Riving Knife AlignmentTo align the blades and riving knife Page Sliding Table Parallelism To adjust the sliding table parallel with the main bladeTo install the crosscut fence To install the crosscut tableCrosscut Table Crosscut FenceTo align the fence scale with the blade Fence Scale AlignmentPower Cord To connect the saw to the power sourceTest Run Operation Safety Operation Tips OperationsPlease follow these tips Every time you use your saw Changing Blades Rip cutting with the sliding table Rip CuttingRip cutting using traditional table saw techniques Crosscutting Fence to Blade on Page 48 if necessary Crosscutting full size panelsTo perform a miter cut Miter CuttingG1955-OxiSolvBlade & Bit Cleaner AccessoriesG7895-Citrus Degreaser G5562-SLIPIT1 Qt. Gel G5563-SLIPIT12 oz SprayH6460-12 Tooth Scoring Blade Set H1300 H1298 G7984 H2347 H0736G3445-Precision Saw Tool H3308-SHOP FOX Push StickH3771-Blade Loc G7581-Superbar G7582-Master PlateCleaning MaintenanceSchedule Unpainted Cast IronSliding table ways LubricationService About ServiceReplacing Belts Page Blade Tilt To square the crosscut fence with the blade Squaring Crosscut Fence to BladeElectrical G0591 single phase magnetic switch Contactor Overload RelaySymptom Possible Cause Possible Solution TroubleshootingLoud repetitious noise coming Main Body PartsG0588/G0591 12 Sliding Table Saws PW01M Flat Washer 8MM PSB02M CAP Screw M6-1 X Saws P0588051 G0588/G0591 12 Sliding Table Saws PN03M G0588/G0591 12 Sliding Table Saws Crosscut Fence G0588/G0591 Rip Fence G0588/G0591 12 Sliding Table Saws Tilt Assembly G0588/G0591 12 Sliding Table Saws PK42M Motor AssemblyG0588/G0591 12 Sliding Table Saws Arbor Assembly G0588/G0591 12 Sliding Table Saws Warranty and Returns Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCPage Call Today For a Free Full Color Catalog