Grizzly G0588, G0591 owner manual Magnetic switch

Page 23

3.Remove the control panel surrounding plate and the cover.

4.Replace the 220V magnetic switch (Figure 7) with the 440V magnetic switch. Set the dial on the new overload relay to 11A.

Note: The magnetic switch consists of the magnetic contactor and the overload relay.

Magnetic

Contactor

	Overload
Overload	Relay Dial

Relay

Figure 7. Magnetic switch.

5.Replace the control panel cover, surrounding plate, and the cover plate.

6.Open the motor cabinet door and remove the motor wiring cover (see Figure 8).

Motor Wiring

Cover

Figure 8. Motor location.

7.Rewire the motor per the diagram on the inside of the motor wiring cover.

G0588/G0591 12" Sliding Table Saws

-15-

Image 23

Contents Sliding Table SAW Sliding Table January This page replaces page 56 of the original manual Sliding Table Parts JanuaryPage G0588/91 Crosscut Fence July Front Support Block G0588/91 Crosscut Fence JulyModel G0588/G0591 Sliding Table SAWPage Table of Contents Operations Contact Info IntroductionForeword Machine Data Sheet Emergency Stop Button Turns Power ON/OFF Buttons Turns the mainBlade Angle Handwheel Adjusts the angle IdentificationPage Safety Instructions for Machinery SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Sliding Table Saws Below are tips to reduce the likelihood of kickback Preventing KickbackProtecting Yourself From Kickback Glossary of Terms Circuit Requirements 220V Single-PhaseWiring 220/440V 3-PhaseControl panel cover plate G0588/G0591 12 Sliding Table Saws Phase Converter Rewiring to GroundingMagnetic switch Description Qty SET UPSet Up Safety Unpacking Items Needed for Set UpSite Considerations Moving & Placing Base UnitCrate Qty Saw Base Unit Not Shown Clean Up InventoryHardware and Tools Blade guard components Edge Shoe Hold DownHardware Recognition Chart Components and Hardware Needed Qty To install the sliding tableSliding Table Extension Tables To install the extension tablesRip Fence and Scale To install the rip fencePage Main Blade To install the bladeScoring Blade To install the scoring bladeTo align the blades and riving knife Aligning BladesRiving Knife Alignment Page Sliding Table Parallelism To adjust the sliding table parallel with the main bladeCrosscut Fence To install the crosscut tableTo install the crosscut fence Crosscut TableTo align the fence scale with the blade Fence Scale AlignmentTest Run Power CordTo connect the saw to the power source Please follow these tips Every time you use your saw Operation Safety Operation TipsOperations Changing Blades Rip cutting with the sliding table Rip CuttingRip cutting using traditional table saw techniques Crosscutting Fence to Blade on Page 48 if necessary Crosscutting full size panelsTo perform a miter cut Miter CuttingG5562-SLIPIT1 Qt. Gel G5563-SLIPIT12 oz Spray AccessoriesG1955-OxiSolvBlade & Bit Cleaner G7895-Citrus DegreaserH6460-12 Tooth Scoring Blade Set H1300 H1298 G7984 H2347 H0736G7581-Superbar G7582-Master Plate H3308-SHOP FOX Push StickG3445-Precision Saw Tool H3771-Blade LocUnpainted Cast Iron MaintenanceCleaning ScheduleSliding table ways LubricationReplacing Belts ServiceAbout Service Page Blade Tilt To square the crosscut fence with the blade Squaring Crosscut Fence to BladeElectrical G0591 single phase magnetic switch Contactor Overload RelaySymptom Possible Cause Possible Solution TroubleshootingLoud repetitious noise coming Main Body PartsG0588/G0591 12 Sliding Table Saws PW01M Flat Washer 8MM PSB02M CAP Screw M6-1 X Saws P0588051 G0588/G0591 12 Sliding Table Saws PN03M G0588/G0591 12 Sliding Table Saws Crosscut Fence G0588/G0591 Rip Fence G0588/G0591 12 Sliding Table Saws Tilt Assembly G0588/G0591 12 Sliding Table Saws PK42M Motor AssemblyG0588/G0591 12 Sliding Table Saws Arbor Assembly G0588/G0591 12 Sliding Table Saws Warranty and Returns Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCPage Call Today For a Free Full Color Catalog