Grizzly G0591 Squaring Crosscut Fence to Blade, To square the crosscut fence with the blade

Page 56

Squaring Crosscut

Fence to Blade

Squaring the crosscut fence to the blade ensures that cuts made with the crosscut fence will be square. This procedure can be done by using a piece of scrap plywood as a test piece and making five test cuts, then adjusting the fence as necessary.

To square the crosscut fence with the blade:

1.Make sure the blade is parallel with the slid- ing table.

2.Prepare the scrap test piece by numbering all four sides as shown in Figure 85.

Figure 85. Fence adjustment test piece.

3.Use the crosscut fence to cut 1⁄2" off of each side of the test piece, then cut side 1 again (make 5 cuts total).

4.Measure the test piece diagonally from cor- ner-to-corner as shown in Figure 85.

—If both measurements are not within 1⁄16", then the crosscut fence needs to be adjust- ed. Proceed to Step 6.

—If both measurements are within 1⁄16" then you are finished with this procedure.

5.Loosen the hex nut shown in Figure 86 and rotate the hex bolt to square the crosscut fence.

Hex Nut

Figure 86. Crosscut fence adjustment cam.

6.Tighten the hex nut and repeat Steps 3-6.

-48-	G0588/G0591 12" Sliding Table Saws

Image 56

Contents Sliding Table SAW Sliding Table January Sliding Table Parts January This page replaces page 56 of the original manualPage G0588/91 Crosscut Fence July G0588/91 Crosscut Fence July Front Support BlockSliding Table SAW Model G0588/G0591Page Table of Contents Operations Contact Info IntroductionForeword Machine Data Sheet Power ON/OFF Buttons Turns the main Blade Angle Handwheel Adjusts the angleIdentification Emergency Stop Button TurnsPage Safety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Sliding Table Saws Below are tips to reduce the likelihood of kickback Preventing KickbackProtecting Yourself From Kickback Glossary of Terms 220V Single-Phase Circuit Requirements220/440V 3-Phase WiringPhase Converter Rewiring to Grounding Control panel cover plate G0588/G0591 12 Sliding Table SawsMagnetic switch SET UP Set Up Safety UnpackingItems Needed for Set Up Description QtyMoving & Placing Base Unit Site ConsiderationsClean Up Inventory Crate Qty Saw Base Unit Not ShownBlade guard components Edge Shoe Hold Down Hardware and ToolsHardware Recognition Chart Components and Hardware Needed Qty To install the sliding tableSliding Table To install the extension tables Extension TablesTo install the rip fence Rip Fence and ScalePage To install the blade Main BladeTo install the scoring blade Scoring BladeTo align the blades and riving knife Aligning BladesRiving Knife Alignment Page To adjust the sliding table parallel with the main blade Sliding Table ParallelismTo install the crosscut table To install the crosscut fenceCrosscut Table Crosscut FenceFence Scale Alignment To align the fence scale with the bladeTest Run Power CordTo connect the saw to the power source Please follow these tips Every time you use your saw Operation Safety Operation TipsOperations Changing Blades Rip Cutting Rip cutting with the sliding tableRip cutting using traditional table saw techniques Crosscutting Crosscutting full size panels Fence to Blade on Page 48 if necessaryMiter Cutting To perform a miter cutAccessories G1955-OxiSolvBlade & Bit CleanerG7895-Citrus Degreaser G5562-SLIPIT1 Qt. Gel G5563-SLIPIT12 oz SprayH1300 H1298 G7984 H2347 H0736 H6460-12 Tooth Scoring Blade SetH3308-SHOP FOX Push Stick G3445-Precision Saw ToolH3771-Blade Loc G7581-Superbar G7582-Master PlateMaintenance CleaningSchedule Unpainted Cast IronLubrication Sliding table ways Replacing Belts Service About Service Page Blade Tilt Squaring Crosscut Fence to Blade To square the crosscut fence with the bladeG0591 single phase magnetic switch Contactor Overload Relay ElectricalTroubleshooting Symptom Possible Cause Possible SolutionLoud repetitious noise coming Parts Main BodyG0588/G0591 12 Sliding Table Saws PW01M Flat Washer 8MM PSB02M CAP Screw M6-1 X Saws P0588051 G0588/G0591 12 Sliding Table Saws PN03M G0588/G0591 12 Sliding Table Saws Crosscut Fence G0588/G0591 Rip Fence G0588/G0591 12 Sliding Table Saws Tilt Assembly G0588/G0591 12 Sliding Table Saws Motor Assembly PK42MG0588/G0591 12 Sliding Table Saws Arbor Assembly G0588/G0591 12 Sliding Table Saws Warranty and Returns Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAPage Call Today For a Free Full Color Catalog