Grizzly G0641 To lubricate the blade arbor housings, To lubricate the main ram pivot point

Page 30

Manual lubrication is required for: 1) blade arbor housings, 2) tie-rod pivot points, and 3) the upper pivot point of the main pneumatic ram.

To lubricate the blade arbor housings:

1.DISCONNECT SAW FROM POWER!

2.DISCONNECT SAW FROM AIR SUPPLY!

3.Raise the front guard up, remove the inner blade guard and blades to access the pivot arm assemblies (see Figure 36).

Blade Arbor Housing

Grease Fitting

Figure 36. Blade arbor housing grease fitting

(left side shown).

4.Clean off the arbor grease fittings, then use a grease gun to add one or two pumps of multi- purpose grease to the arbor housing grease fittings.

5.Re-install the inner blade guard and blades, then lower and secure the front guard before continuing operation.

NOTICE

Adding more than one or two pumps to the arbor housing may cause damage to the seals and require replacement.

To lubricate the tie-rod pivot points:

1.DISCONNECT SAW FROM POWER!

2.DISCONNECT SAW FROM AIR SUPPLY!

-28-

3.Raise the front guard up, and remove the inner blade guard and blades to access the tie-rods (see Figure 37).

Pivot

Points

Figure 37. Tie-rod pivot points (one side shown).

4.Brush a small amount of multi-purpose grease on and around the tie-rod pivot points.

5.Re-install the inner blade guard and blades, then lower and secure the front guard before continuing operation.

To lubricate the main ram pivot point:

1.DISCONNECT SAW FROM POWER!

2.Remove the rear cabinet access panel.

3.Brush a small amount of multi-purpose grease on and around the main ram pivot point (see Figure 38).

Main Ram

Pivot Point

Figure 38. Main pneumatic ram pivot point (shown through the rear cabinet access).

G0641 Double Miter Saw

Image 30
Contents Model G0641 Double Miter SAW Page Table of Contents Introduction ForewordContact Info Machine Data Sheet Identification Model G0641 identificationSafety Instructions for Machinery G0641 Double Miter Saw Safety Instructions for Double Miter Saws 220V Single-Phase Circuit RequirementsItems Needed for Setup SetupSetup Safety UnpackingInventory Inventory Figures QtyClean Up Site ConsiderationsMoving & Placing Machine To move the machineMounting to Shop Floor Bolting to Concrete FloorsAssembly To assemble the double miter sawAir Supply To connect the saw to compressed airDust Collection To connect a dust collection hoseTest Run To test run the machineOperation Safety OperationsTo make a cut Hold-downs To adjust the lowering and raising rate of the saw blades To adjust the lowering rate of the hold- downsLowering Speeds Fence Stop Replacing Blades To replace the saw bladesG8982-Shop Fox Roller Table AccessoriesG1955-OxiSolvBlade & Bit Cleaner Forest ChopMaster H4751-12, 80 TPI, 1 ArborBoeshield T20448T20452 T20501 T20456 H0736G3326-BesseyAngle Clamp H8888-Kreg Framing TableMaintenance CleaningSchedule Lubrication To lubricate the pneumatic systemTo lubricate the lower pivot arms To lubricate the blade arbor housings To lubricate the main ram pivot pointBelt Maintenance To re-tension/replace the V-beltsPage Service TroubleshootingMiter Saw Operations Pneumatic System Aligning Pivot Arm Assembly To realign the pivot arm assembliesPneumatic Limit Switch Electrical Wiring Diagram JunctionMotor Wiring Diagram Left-handPneumatic System Diagram Parts Cabinet BreakdownCabinet Parts List DescriptionDrive System Breakdown Drive System Parts List Pivot Linkage Breakdown & Parts List Extension Wings Breakdown & Parts List Electrical & Lubrication Systems Breakdown Electrical & Lubrication Systems Parts List Pneumatic System Breakdown Pneumatic System Parts List Label Placement & List G0641 Double Miter Saw Page Page Warranty and Returns