Grizzly G0605X/G0606X owner manual Example of switching incoming power

Page 30

12.Model G0606X only: Verify that the power is not connected out of phase by starting/stop- ping the table saw and determining if the motor turns in the correct direction, using the criteria below:

—If the blade turns clockwise (as standing in front of the table saw), it is turning in the correct direction.

—If the blade turns counterclockwise, toward the back of the saw, it is turning in the wrong direction.

Stop the table saw, shut OFF the power source, swap any two of the three power wires—L1, L2, or L3—that connect to the saw. If using a phase converter for 220V 3- phase operation, ONLY swap L1 and L2.

13.Verify that the arbor nut is secure. The saw is now ready to operate.

��	��	��
Incoming
Power
Wires
��			Contactor
�	��	��	Contactor
�		��
	��	��	��
			��
Figure 35. Example of switching incoming power
	wires.

-28-	G0605X/G0606X Extreme Series 12" Table Saw

Image 30

Contents Extreme Series Table SAW Page Table of Contents Accessories Maintenance Introduction ForewordContact Info Machine Data Sheet Model G0606X 12 Extreme Series Table SAW Identification G0606X identificationSafety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Table Saws Preventing Kickback Protecting Yourself From KickbackBelow are tips to avoid the most common causes of kickback Glossary of Terms Operation Power Connection DeviceCircuit Requirements Full Load Amperage Draw DrawPhase Converter Precaution 440V ConversionExtension Cords 220V Only Items Needed for Set Up SET UPSet Up Safety UnpackingMachine Inventory Fence InventoryFence Rail Inventory Extension Table Inventory Outfeed Table InventoryHardware Recognition Chart Site Considerations Clean UpPlacement Location Floor LoadTo install the front and rear rails Extension TableComponents and Hardware Needed Qty Foot installed on support leg To install the outfeed table Outfeed TableTo install the blade Saw BladeTo install and adjust the table insert Arbor Table InsertTo change the arbor To install the blade guard Blade Guard SplitterOn/Off Switch Riving KnifeMiter Gauge Fence Components Dust CollectionTo connect a dust collection hose Test Run Recommended AdjustmentsRecommended adjustment checklist To test run the machineExample of switching incoming power Operation Safety OperationsBasic Controls Crosscut blade features Disabling On/Off SwitchRipping blade features Combination blade featuresLaminate blade features Dado BladesNon-Through Cuts Workpiece InspectionNon-Through Through Cuts Through CutsRipping Typical ripping operationTo make a crosscut using the miter gauge Crosscutting Miter CutsTo perform a miter cut Dado Cutting To use a standard saw blade to cut dadoes Rabbet Cutting To cut rabbets with the dado bladeTo cut rabbets with the standard blade Resawing Resaw Barrier Auxiliary FenceResawing Operations Components Needed for ResawingPage H1234-Table Saw Bench Guide AccessoriesG7895-Citrus Degreaser H7583-Grizzly Tenoning JigG7581-Superbar G7582-Master Plate G2370-SHOP FOX Board BuddiesSchedule MaintenanceCleaning LubricationService TroubleshootingMotor & Electrical Table Saw Operations Replacing Flat Belt Tools Needed QtyTo remove the flat belt To install the new belt Blade Tilt Stops To set the 90 stop boltTo set the 45 stop bolt To adjust the tilt indicator arrow Digital ReadoutTo set the digital readout To adjust the blade parallel to the miter slot Miter Slot to Blade ParallelismShim procedure diagram a Blade Alignment Adjusting FenceTo adjust the blade by moving the table Square and HeightMiter Gauge G0605X/G0606X Electrical Components G0605X motor junction boxG0605X Wiring Diagram G0606X magnetic switch prewired to Phase G0606X Electrical ComponentsG0606X Wiring Diagram G0606X Wiring Diagram Cabinet, Motor & Main Table Breakdown Cabinet, Motor & Main Table Parts List DescriptionDescription Blade Guard Assembly Breakdown Blade Guard Parts List Fence Assembly Breakdown Fence Parts List Miter Gauge Assembly Breakdown Miter Gauge Parts List Extension Table Assembly Outfeed Table Assembly Breakdown Outfeed Table Parts List Guard and ANTI-KICK Back Label Warranty and Returns Page Page