Grizzly G0605X/G0606X Accessories, G7895-Citrus Degreaser, H1234-Table Saw Bench Guide

Page 45

ACCESSORIES

SECTION 5: ACCESSORIES

H8084—Rear Tool Box for G0605X/G0606X H8085—Front Tool Box for G0605X/G0606X Made specially to fit the G0605X/G0606X saws. These heavy-duty tool boxes feature powder coated paint and ball bearing slides. Model H8084, 32"L x 221/2"H x 15"D; Model H8085, 25"L x 221/2"H x 15"D.

Figure 58. Model H8084, H8085 Tool Boxes.

G7895—Citrus Degreaser

This citrus based degreaser is perfect for clean- ing cosmoline off of new equipment. It also works for cleaning auto parts, tools, concrete, and porcelain surfaces. Natural, safe for the environ- ment, and contains no CFC’s.

H1234—Table Saw Bench Guide

Like having a master woodworker by your side. Inside this book you'll find great ideas for doz- ens of shop-made accessories and jigs, in-depth maintenance procedures, loads of safety tips and tricks, and picture-laden walkthroughs for nearly every cut imaginable. Also includes a blade section that covers selection, sharpening, care, troubleshooting, etc. A must have! 160 pages.

Figure 60. H1234 Table Saw Bench Guide.

H9910—Phenolic Dado Insert for G0605X/ G0606X

H9911—Zero Clearance Insert for G0605X/ G0606X

Made especially for the G0605X/G0606X table saw. Height is easily adjustable. Special phenolic material.

H7583—Grizzly Tenoning Jig

Our fully adjustable tenoning jig handles stock up to 31⁄4" thick and features an adjustable bevel angle with a 90° to 75° range. The two large grip handles, adjustable guide bar, multi-position con- trol levers, and extra large clamping handwheel will ensure accurate and repeatable results. A top seller!

Figure 59. G7895 Citrus Degreaser.

G0605X/G0606X Extreme Series 12" Table Saw

-43-

Image 45

Contents Extreme Series Table SAW Page Table of Contents Accessories Maintenance Introduction ForewordContact Info Machine Data Sheet Model G0606X 12 Extreme Series Table SAW G0606X identification IdentificationSafety Instructions for Machinery SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Table Saws Preventing Kickback Protecting Yourself From KickbackBelow are tips to avoid the most common causes of kickback Glossary of Terms Circuit Requirements Power Connection DeviceOperation Full Load Amperage Draw DrawPhase Converter Precaution 440V ConversionExtension Cords 220V Only Set Up Safety SET UPItems Needed for Set Up UnpackingMachine Inventory Fence InventoryFence Rail Inventory Outfeed Table Inventory Extension Table InventoryHardware Recognition Chart Placement Location Clean UpSite Considerations Floor LoadTo install the front and rear rails Extension TableComponents and Hardware Needed Qty Foot installed on support leg Outfeed Table To install the outfeed tableSaw Blade To install the bladeTo install and adjust the table insert Arbor Table InsertTo change the arbor Blade Guard Splitter To install the blade guardOn/Off Switch Riving KnifeMiter Gauge Fence Components Dust CollectionTo connect a dust collection hose Recommended adjustment checklist Recommended AdjustmentsTest Run To test run the machineExample of switching incoming power Operation Safety OperationsBasic Controls Ripping blade features Disabling On/Off SwitchCrosscut blade features Combination blade featuresDado Blades Laminate blade featuresNon-Through Through Cuts Workpiece InspectionNon-Through Cuts Through CutsTypical ripping operation RippingTo make a crosscut using the miter gauge Crosscutting Miter CutsTo perform a miter cut Dado Cutting To use a standard saw blade to cut dadoes To cut rabbets with the dado blade Rabbet CuttingTo cut rabbets with the standard blade Resawing Auxiliary Fence Resaw BarrierComponents Needed for Resawing Resawing OperationsPage G7895-Citrus Degreaser AccessoriesH1234-Table Saw Bench Guide H7583-Grizzly Tenoning JigG2370-SHOP FOX Board Buddies G7581-Superbar G7582-Master PlateCleaning MaintenanceSchedule LubricationService TroubleshootingMotor & Electrical Table Saw Operations Replacing Flat Belt Tools Needed QtyTo remove the flat belt To install the new belt Blade Tilt Stops To set the 90 stop boltTo set the 45 stop bolt To adjust the tilt indicator arrow Digital ReadoutTo set the digital readout Miter Slot to Blade Parallelism To adjust the blade parallel to the miter slotShim procedure diagram a To adjust the blade by moving the table Adjusting FenceBlade Alignment Square and HeightMiter Gauge G0605X motor junction box G0605X/G0606X Electrical ComponentsG0605X Wiring Diagram G0606X Electrical Components G0606X magnetic switch prewired to PhaseG0606X Wiring Diagram G0606X Wiring Diagram Cabinet, Motor & Main Table Breakdown Description Cabinet, Motor & Main Table Parts ListDescription Blade Guard Assembly Breakdown Blade Guard Parts List Fence Assembly Breakdown Fence Parts List Miter Gauge Assembly Breakdown Miter Gauge Parts List Extension Table Assembly Outfeed Table Assembly Breakdown Outfeed Table Parts List Guard and ANTI-KICK Back Label Warranty and Returns Page Page