Grizzly G0605X/G0606X owner manual Service, Troubleshooting, Motor & Electrical

Page 48

SECTION 7: SERVICE

Review the troubleshooting and procedures in this section to fix your machine if a problem develops. If you need replacement parts or you are unsure of your repair skills, then feel free to call our Technical Support at (570) 546-9663.

Troubleshooting

Motor & Electrical

Symptom		Possible Cause		Possible Solution
Machine	does not	1.	Plug/receptacle is at fault or wired incor-	1.	Test for good contacts; correct the wiring.
start or	a breaker		rectly.
trips.		2.	Start capacitor is at fault (G0605X only).	2.	Test/replace if faulty.
		2.	Start capacitor is at fault (G0605X only).	2.	Test/replace if faulty.
		3.	Motor connection wired incorrectly.	3.	Correct motor wiring connections.
		4.	Thermal overload relay has tripped.	4.	Unplug machine, open magnetic switch cover, turn
					amperage dial on Thermal Protection Circuit Breaker
					to a higher amperage setting.
		5.	Contactor not getting energized/has burnt	5.	Test for power on all legs and contactor operation.
			contacts.		Replace unit if faulty.
		6.	Wall fuse/circuit breaker is blown/tripped.	6.	Ensure correct size for machine load (refer to Page
					12); replace weak breaker.
		7.	Power supply is at fault/switched OFF.	7.	Ensure hot lines have correct voltage on all legs and
					main power supply is switched ON.
		8.	Motor ON button or ON/OFF switch is at	8.	Replace faulty ON button or ON/OFF switch.
			fault.
		9.	Centrifugal Switch is at fault (G0605X	9.	Adjust/replace the centrifugal switch if available.
			only).
		10. Wiring is open/has high resistance.		10. Check for broken wires or disconnected/corroded
					connections, and repair/replace as necessary.
		11. Motor is at fault.		11. Test/repair/replace.
		12. Start delay module is at fault.		12. Adjust to correct delay; replace module.

Machine stalls or is		1.	Applying too much pressure to workpiece.	1.	Use sharp blade, and reduce the feed rate.
underpowered.		2.	Run capacitor is at fault (G0605X only).	2.	Test/repair/replace.
		3.	Belt slipping.	3.	Replace bad belt, align pulleys, and re-tension.
		4.	Motor connection is wired incorrectly.	4.	Correct motor wiring connections.
		5.	Plug/receptacle is at fault.	5.	Test for good contacts; correct the wiring.
		6.	Motor bearings are at fault.	6.	Test by rotating shaft; rotational grinding/loose shaft
					requires bearing replacement.
		7.	Motor has overheated.	7.	Clean off motor, let cool, and reduce workload.
		8.	Contactor not getting energized or has poor	8.	Test for power on all legs and contactor operation.
			contacts.		Replace if faulty.
		9.	Motor is at fault.	9.	Test/repair/replace.
		10. Centrifugal switch is at fault (G0605X).		10. Adjust/replace centrifugal switch if available.
		11. Start delay module at fault (G0606X only).		11. Adjust to correct delay; replace module.

-46-	G0605X/G0606X Extreme Series 12" Table Saw

Image 48

Contents Extreme Series Table SAW Page Table of Contents Accessories Maintenance Introduction ForewordContact Info Machine Data Sheet Model G0606X 12 Extreme Series Table SAW Identification G0606X identificationSafety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Table Saws Preventing Kickback Protecting Yourself From KickbackBelow are tips to avoid the most common causes of kickback Glossary of Terms Power Connection Device Circuit RequirementsOperation Full Load Amperage Draw DrawPhase Converter Precaution 440V ConversionExtension Cords 220V Only SET UP Set Up SafetyItems Needed for Set Up UnpackingMachine Inventory Fence InventoryFence Rail Inventory Extension Table Inventory Outfeed Table InventoryHardware Recognition Chart Clean Up Placement LocationSite Considerations Floor LoadTo install the front and rear rails Extension TableComponents and Hardware Needed Qty Foot installed on support leg To install the outfeed table Outfeed TableTo install the blade Saw BladeTo install and adjust the table insert Arbor Table InsertTo change the arbor To install the blade guard Blade Guard SplitterOn/Off Switch Riving KnifeMiter Gauge Fence Components Dust CollectionTo connect a dust collection hose Recommended Adjustments Recommended adjustment checklistTest Run To test run the machineExample of switching incoming power Operation Safety OperationsBasic Controls Disabling On/Off Switch Ripping blade featuresCrosscut blade features Combination blade featuresLaminate blade features Dado BladesWorkpiece Inspection Non-Through Through CutsNon-Through Cuts Through CutsRipping Typical ripping operationTo make a crosscut using the miter gauge Crosscutting Miter CutsTo perform a miter cut Dado Cutting To use a standard saw blade to cut dadoes Rabbet Cutting To cut rabbets with the dado bladeTo cut rabbets with the standard blade Resawing Resaw Barrier Auxiliary FenceResawing Operations Components Needed for ResawingPage Accessories G7895-Citrus DegreaserH1234-Table Saw Bench Guide H7583-Grizzly Tenoning JigG7581-Superbar G7582-Master Plate G2370-SHOP FOX Board BuddiesMaintenance CleaningSchedule LubricationService TroubleshootingMotor & Electrical Table Saw Operations Replacing Flat Belt Tools Needed QtyTo remove the flat belt To install the new belt Blade Tilt Stops To set the 90 stop boltTo set the 45 stop bolt To adjust the tilt indicator arrow Digital ReadoutTo set the digital readout To adjust the blade parallel to the miter slot Miter Slot to Blade ParallelismShim procedure diagram a Adjusting Fence To adjust the blade by moving the tableBlade Alignment Square and HeightMiter Gauge G0605X/G0606X Electrical Components G0605X motor junction boxG0605X Wiring Diagram G0606X magnetic switch prewired to Phase G0606X Electrical ComponentsG0606X Wiring Diagram G0606X Wiring Diagram Cabinet, Motor & Main Table Breakdown Cabinet, Motor & Main Table Parts List DescriptionDescription Blade Guard Assembly Breakdown Blade Guard Parts List Fence Assembly Breakdown Fence Parts List Miter Gauge Assembly Breakdown Miter Gauge Parts List Extension Table Assembly Outfeed Table Assembly Breakdown Outfeed Table Parts List Guard and ANTI-KICK Back Label Warranty and Returns Page Page