Grizzly G0605X/G0606X Disabling On/Off Switch, Blade Selection, Ripping blade features

Page 32

Disabling On/Off

Switch

To disable the saw and prevent accidental startup, insert the safety pin through the holes in the ON button, and insert the end of the chain into the pin as shown in Figure 37.

Safety

Pin

Safety Pin

Figure 37. Disabling switch.

Blade Selection

Ripping blade features:

•Best for cutting with the grain of the workpiece.

•20-40 teeth.

•Flat-top ground tooth profile.

•Large gullets for large chip removal.

��

��

��

Figure 38. Ripping blade.

-30-

Crosscut blade features:

•Best for cutting across the grain of the workpiece.

•60-80 teeth.

•Alternate top bevel tooth profile.

•Small hook angle and a shallow gullet.

��

��

��

Figure 39. Crosscutting blade.

Combination blade features:

•Adequate for cutting both with and across the grain.

•40-50 teeth.

•Alternate top bevel and flat, or alternate top bevel and raker tooth profile.

•Teeth are arranged in groups of five.

•Gullets are small and shallow within the groups of five teeth, similar to a cross-cut blade; then large and deep between each group of five, like a ripping blade.

��

��

��

��

��

Figure 40. Combination blade.

G0605X/G0606X Extreme Series 12" Table Saw

Image 32

Contents Extreme Series Table SAW Page Table of Contents Accessories Maintenance Contact Info IntroductionForeword Machine Data Sheet Model G0606X 12 Extreme Series Table SAW Identification G0606X identificationSafety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Table Saws Below are tips to avoid the most common causes of kickback Preventing KickbackProtecting Yourself From Kickback Glossary of Terms Power Connection Device Circuit RequirementsOperation Full Load Amperage Draw DrawExtension Cords 220V Only Phase Converter Precaution440V Conversion SET UP Set Up SafetyItems Needed for Set Up UnpackingFence Rail Inventory Machine InventoryFence Inventory Extension Table Inventory Outfeed Table InventoryHardware Recognition Chart Clean Up Placement LocationSite Considerations Floor LoadComponents and Hardware Needed Qty To install the front and rear railsExtension Table Foot installed on support leg To install the outfeed table Outfeed TableTo install the blade Saw BladeTo change the arbor To install and adjust the table insertArbor Table Insert To install the blade guard Blade Guard SplitterMiter Gauge On/Off SwitchRiving Knife To connect a dust collection hose Fence ComponentsDust Collection Recommended Adjustments Recommended adjustment checklistTest Run To test run the machineExample of switching incoming power Basic Controls Operation SafetyOperations Disabling On/Off Switch Ripping blade featuresCrosscut blade features Combination blade featuresLaminate blade features Dado BladesWorkpiece Inspection Non-Through Through CutsNon-Through Cuts Through CutsRipping Typical ripping operationTo perform a miter cut To make a crosscut using the miter gaugeCrosscutting Miter Cuts Dado Cutting To use a standard saw blade to cut dadoes Rabbet Cutting To cut rabbets with the dado bladeTo cut rabbets with the standard blade Resawing Resaw Barrier Auxiliary FenceResawing Operations Components Needed for ResawingPage Accessories G7895-Citrus DegreaserH1234-Table Saw Bench Guide H7583-Grizzly Tenoning JigG7581-Superbar G7582-Master Plate G2370-SHOP FOX Board BuddiesMaintenance CleaningSchedule LubricationMotor & Electrical ServiceTroubleshooting Table Saw Operations To remove the flat belt Replacing Flat BeltTools Needed Qty To install the new belt To set the 45 stop bolt Blade Tilt StopsTo set the 90 stop bolt To set the digital readout To adjust the tilt indicator arrowDigital Readout To adjust the blade parallel to the miter slot Miter Slot to Blade ParallelismShim procedure diagram a Adjusting Fence To adjust the blade by moving the tableBlade Alignment Square and HeightMiter Gauge G0605X/G0606X Electrical Components G0605X motor junction boxG0605X Wiring Diagram G0606X magnetic switch prewired to Phase G0606X Electrical ComponentsG0606X Wiring Diagram G0606X Wiring Diagram Cabinet, Motor & Main Table Breakdown Cabinet, Motor & Main Table Parts List DescriptionDescription Blade Guard Assembly Breakdown Blade Guard Parts List Fence Assembly Breakdown Fence Parts List Miter Gauge Assembly Breakdown Miter Gauge Parts List Extension Table Assembly Outfeed Table Assembly Breakdown Outfeed Table Parts List Guard and ANTI-KICK Back Label Warranty and Returns Page Page