Grizzly G0605X/G0606X owner manual Machine Data Sheet

Page 6

MACHINE DATA

SHEET

Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901

MODEL G0605X 12" EXTREME SERIES TABLE SAW

Overall Dimensions:
Table Height		353⁄4"
Table Size		303⁄4" D x 241⁄2" W
Table Size w/Extension		303⁄4" D x 783⁄4" W
Overall Size when Fully Assembled		91" W x 93" L x 421⁄2"H
Miter Gauge T-Slot		3⁄4" W x 3⁄8" D
Blade Tilt		Left 0-45°
Shipping Weight (5 Boxes)		967 lbs.
Machine Weight		715 lbs.
Footprint		581⁄2" W x 661⁄2" L
Cutting Capacities:
Blade Size		12"
Maximum Depth Of Cut @ 90°		4"
Maximum Depth Of Cut @ 45°		23⁄4"
Maximum Rip Capacity To Right Of Blade		52"
Distance From Front Of Table To Center Of Blade		171⁄4"
Distance From Front Of Table To Front Of Blade		131⁄2"
Maximum Width Of Dado Cut		1"
Motor:
Type		TEFC Capacitor Start Induction
Horsepower		5 HP
Phase/Cycle		Single-Phase/60 Hz
Voltage		220V
Amps		23A
RPM		3450
Power Transfer		Belt Drive
Power Switch		On/Off Push Button, Magnetic
Construction:
Main Table		Precision-Ground Cast Iron
Cabinet		Pre-Formed Steel
Miter Gauge		Aluminum Body/Steel Miter Bar
Trunnions		Cast Iron
Bearings		Sealed & Permanently Lubricated
Fence	T-Shape, Front Locking, Aluminum Extruded Body
Arbor Shaft:
Dimensions		1" Diameter
Speed		3600 RPM

Features:

........................................... Included Outfeed & Extension Tables w/Storage Shelves

.......................................................................................................... Digital Tilt Gauge

...................................................................................................................Riving Knife

......................................................................................................Hinged Motor Cover

...................................................................................................................4" Dust Port

........................................................................................................Included 12" Blade

...................................Arbor Can Be Changed to Accomodate 5/8" or 1" Arbor Blades

Specifications, while deemed accurate, are not guaranteed.

-4-	G0605X/G0606X Extreme Series 12" Table Saw

Image 6

Contents Extreme Series Table SAW Page Table of Contents Accessories Maintenance Introduction ForewordContact Info Machine Data Sheet Model G0606X 12 Extreme Series Table SAW Identification G0606X identificationSafety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Table Saws Preventing Kickback Protecting Yourself From KickbackBelow are tips to avoid the most common causes of kickback Glossary of Terms Operation Power Connection DeviceCircuit Requirements Full Load Amperage Draw DrawPhase Converter Precaution 440V ConversionExtension Cords 220V Only Items Needed for Set Up SET UPSet Up Safety UnpackingMachine Inventory Fence InventoryFence Rail Inventory Extension Table Inventory Outfeed Table InventoryHardware Recognition Chart Site Considerations Clean UpPlacement Location Floor LoadTo install the front and rear rails Extension TableComponents and Hardware Needed Qty Foot installed on support leg To install the outfeed table Outfeed TableTo install the blade Saw BladeTo install and adjust the table insert Arbor Table InsertTo change the arbor To install the blade guard Blade Guard SplitterOn/Off Switch Riving KnifeMiter Gauge Fence Components Dust CollectionTo connect a dust collection hose Test Run Recommended AdjustmentsRecommended adjustment checklist To test run the machineExample of switching incoming power Operation Safety OperationsBasic Controls Crosscut blade features Disabling On/Off SwitchRipping blade features Combination blade featuresLaminate blade features Dado BladesNon-Through Cuts Workpiece InspectionNon-Through Through Cuts Through CutsRipping Typical ripping operationTo make a crosscut using the miter gauge Crosscutting Miter CutsTo perform a miter cut Dado Cutting To use a standard saw blade to cut dadoes Rabbet Cutting To cut rabbets with the dado bladeTo cut rabbets with the standard blade Resawing Resaw Barrier Auxiliary FenceResawing Operations Components Needed for ResawingPage H1234-Table Saw Bench Guide AccessoriesG7895-Citrus Degreaser H7583-Grizzly Tenoning JigG7581-Superbar G7582-Master Plate G2370-SHOP FOX Board BuddiesSchedule MaintenanceCleaning LubricationService TroubleshootingMotor & Electrical Table Saw Operations Replacing Flat Belt Tools Needed QtyTo remove the flat belt To install the new belt Blade Tilt Stops To set the 90 stop boltTo set the 45 stop bolt To adjust the tilt indicator arrow Digital ReadoutTo set the digital readout To adjust the blade parallel to the miter slot Miter Slot to Blade ParallelismShim procedure diagram a Blade Alignment Adjusting FenceTo adjust the blade by moving the table Square and HeightMiter Gauge G0605X/G0606X Electrical Components G0605X motor junction boxG0605X Wiring Diagram G0606X magnetic switch prewired to Phase G0606X Electrical ComponentsG0606X Wiring Diagram G0606X Wiring Diagram Cabinet, Motor & Main Table Breakdown Cabinet, Motor & Main Table Parts List DescriptionDescription Blade Guard Assembly Breakdown Blade Guard Parts List Fence Assembly Breakdown Fence Parts List Miter Gauge Assembly Breakdown Miter Gauge Parts List Extension Table Assembly Outfeed Table Assembly Breakdown Outfeed Table Parts List Guard and ANTI-KICK Back Label Warranty and Returns Page Page