Grizzly G0605X/G0606X G0606X Electrical Components, G0606X magnetic switch prewired to Phase

Page 60

G0606X Electrical Components

Figure 89. G0606X magnetic switch prewired to 220V,

3-phase.

Figure 90. G0606X magnetic switch converted to

440V, 3-phase.

Note: The thermal relay in Figure 89 is set for 22 amp, 220V, 3-phase operation.

Note: The therrmal relay in Figure 90 is adjusted for 11 amp, 440V, 3-phase operation.

-58-

G0605X/G0606X Extreme Series 12" Table Saw

Page 59 Page 61
Image 60
Page 59 Page 61
Contents Extreme Series Table SAW Page Table of Contents Accessories Maintenance Introduction ForewordContact Info Machine Data Sheet Model G0606X 12 Extreme Series Table SAW Identification G0606X identificationSafety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Table Saws Preventing Kickback Protecting Yourself From KickbackBelow are tips to avoid the most common causes of kickback Glossary of Terms Power Connection Device Circuit RequirementsOperation Full Load Amperage Draw DrawPhase Converter Precaution 440V ConversionExtension Cords 220V Only SET UP Set Up SafetyItems Needed for Set Up UnpackingMachine Inventory Fence InventoryFence Rail Inventory Extension Table Inventory Outfeed Table InventoryHardware Recognition Chart Clean Up Placement LocationSite Considerations Floor LoadTo install the front and rear rails Extension TableComponents and Hardware Needed Qty Foot installed on support leg To install the outfeed table Outfeed TableTo install the blade Saw BladeTo install and adjust the table insert Arbor Table InsertTo change the arbor To install the blade guard Blade Guard SplitterOn/Off Switch Riving KnifeMiter Gauge Fence Components Dust CollectionTo connect a dust collection hose Recommended Adjustments Recommended adjustment checklistTest Run To test run the machineExample of switching incoming power Operation Safety OperationsBasic Controls Disabling On/Off Switch Ripping blade featuresCrosscut blade features Combination blade featuresLaminate blade features Dado BladesWorkpiece Inspection Non-Through Through CutsNon-Through Cuts Through CutsRipping Typical ripping operationTo make a crosscut using the miter gauge Crosscutting Miter CutsTo perform a miter cut Dado Cutting To use a standard saw blade to cut dadoes Rabbet Cutting To cut rabbets with the dado bladeTo cut rabbets with the standard blade Resawing Resaw Barrier Auxiliary FenceResawing Operations Components Needed for ResawingPage Accessories G7895-Citrus DegreaserH1234-Table Saw Bench Guide H7583-Grizzly Tenoning JigG7581-Superbar G7582-Master Plate G2370-SHOP FOX Board BuddiesMaintenance CleaningSchedule LubricationService TroubleshootingMotor & Electrical Table Saw Operations Replacing Flat Belt Tools Needed QtyTo remove the flat belt To install the new belt Blade Tilt Stops To set the 90 stop boltTo set the 45 stop bolt To adjust the tilt indicator arrow Digital ReadoutTo set the digital readout To adjust the blade parallel to the miter slot Miter Slot to Blade ParallelismShim procedure diagram a Adjusting Fence To adjust the blade by moving the tableBlade Alignment Square and HeightMiter Gauge G0605X/G0606X Electrical Components G0605X motor junction boxG0605X Wiring Diagram G0606X magnetic switch prewired to Phase G0606X Electrical ComponentsG0606X Wiring Diagram G0606X Wiring Diagram Cabinet, Motor & Main Table Breakdown Cabinet, Motor & Main Table Parts List DescriptionDescription Blade Guard Assembly Breakdown Blade Guard Parts List Fence Assembly Breakdown Fence Parts List Miter Gauge Assembly Breakdown Miter Gauge Parts List Extension Table Assembly Outfeed Table Assembly Breakdown Outfeed Table Parts List Guard and ANTI-KICK Back Label Warranty and Returns Page Page
Top Page Image Contents