Grizzly G0636X owner manual Test Run, To test run the machine

Page 22

Test Run

Once the assembly is complete, test run your machine to make sure it runs properly and is ready for regular operation.

The test run consists of verifying the following: 1) The motor powers up and runs correctly, 2) the safety disabling mechanism on the switch works correctly, and 3) the stop button safety feature works correctly.

If, during the test run, you cannot easily locate the source of an unusual noise or vibration, stop using the machine immediately, then review Troubleshooting on Page 42.

If you still cannot remedy a problem, contact our Tech Support at (570) 546-9663 for assistance.

To test run the machine:

1.Make sure you have read the safety instruc- tions at the beginning of the manual and that the machine is setup properly.

2.Make sure all tools and objects used during setup are cleared away from the machine.

3.Connect the machine to the power source.

4.Verify that the machine is operating correctly by turning the switch disabling key (Figure 20) to "1" and turning the machine ON.

—When operating correctly, the machine runs smoothly with little or no vibration or rubbing noises.

—Investigate and correct strange or unusual noises or vibrations before operating the machine further. Always disconnect the machine from power when investigating or correcting potential problems.

Figure 20. G0636X switch disabling key and

ON/OFF switch.

5.Press the OFF button to stop the machine.

6.WITHOUT resetting the OFF button, press the ON button. The machine should not start.

—If the machine does not start, the OFF but- ton safety feature is working correctly.

—If the machine does start (with the stop button pushed in), immediately disconnect power to the machine. The OFF button safety feature is not working correctly. This safety feature must work properly before proceeding with regular operations. Call Tech Support for help.

7.Push the OFF button in, then twist it clock- wise so it pops out. When the OFF button pops out, the switch is reset and ready for operation (see Figure 21).

���

�

�

��������

������������

���������

�����������������

���

Figure 21. Resetting the switch.

8.Turn the switch disabling key to "0", as shown

in Figure 20.

-20-

G0636X 17" Ultimate Bandsaw

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Model G0636X Ultimate Bandsaw Page Table of Contents Foreword IntroductionContact Info Machine Data Sheet G0636X 17 Ultimate Bandsaw Identification Safety Instructions for Machinery G0636X 17 Ultimate Bandsaw Additional Safety Instructions for Bandsaws 220V Single-Phase Circuit RequirementsItems Needed for Setup SetupSetup Safety UnpackingInventory Crate Contents Figure QtyHardware and Tools Qty Hardware Recognition Chart Site Considerations Clean UpPlacement Location Floor LoadMoving & Placing Base Unit To move and place the bandsaw using wood shimsTo move and place the bandsaw Guide Post Handwheel To install the guide post handwheelMounting to Shop Floor Bolting to Concrete FloorsBlade Tracking To center track the bladePositive Stop To set the positive stopDust Collection To connect a dust collection hoseTo install the fence handle FenceTest Run To test run the machineTensioning Blade Adjusting Blade Guide BearingsTo adjust the upper blade guides To tension the bandsaw bladeLateral adjustment of blade guides Adjusting Support Bearings To adjust the upper support bearingTo adjust the lower support bearing Aligning Table Aligning Fence To align the fence parallel with the miter slotTo calibrate the pointer Pointer CalibrationMiter Gauge To calibrate the miter gaugeOperations Operation SafetyOverview Foot Brake Guide PostTo correct blade lead Fine Tune TrackingBlade Lead To skew your fenceTo shift the table Table TiltTo tilt the table To make a rip cut RippingCrosscuttingTo make a 90˚ crosscut Resawing Cutting CurvesBlade Length Stacked CutsBlade Information Blade WidthBlade Care Tooth StyleTooth Pitch Blade BreakageTo remove a blade Blade ChangesMost common causes of blade breakage are To replace a bladeCarbon Steel Replacement Blades for the Model G0636X AccessoriesReplacement Blades Timber Wolf Replacement Blades for the Model G0636XH2347 H1300 H1298 G7984 H0736 H1302Maintenance To lubricate the blade guide rack and pinion To lubricate the tension adjustment assem- blyTo lubricate the blade tracking knob To lubricate the table tilt rack and pinion assembly To lubricate the trunnionsTroubleshooting ServiceMotor & Electrical Symptom Possible Cause Possible Solution Cutting OperationsTo check the V-belts Checking Tensioning V-BeltsTools Needed Qty To tension the V-beltReplacing V-Belts Adjusting TensionTo adjust the tension lever LeverWheel Alignment Adjusting Wheel Blade BrushesTo adjust the brushes Components and Hardware Needed QtyDimensions of coplanarity gauge G0636X 17 Ultimate Bandsaw Coplanarity Gauge Power supply terminal box Electrical ComponentsWiring Diagram See FigureBreakdown Parts Parts List DescriptionPower Cord Support Plate Labels/Cosmetic Parts Warranty and Returns G0636X 17 Ultimate Bandsaw Page Page
Top Page Image Contents