Grizzly G0636X owner manual Maintenance

Page 41

SECTION 6: MAINTENANCE

Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious person- al injury.

Schedule

For optimum performance from your machine, follow this maintenance schedule and refer to any specific instructions given in this section.

Daily Check:

Loose mounting bolts.

Damaged saw blade.

Worn or damaged wires.

Any other unsafe condition.

Monthly Check:

V-belt tension, damage, or wear.

Clean/vacuum dust buildup from inside cabi- net and off motor.

Cleaning

Cleaning the Model G0636X is relatively easy. Vacuum excess wood chips and sawdust, and wipe off the remaining dust with a dry cloth. If any resin has built up, use a resin dissolving cleaner to remove it. Treat all unpainted cast iron and steel with a non-staining lubricant after cleaning.

G0636X 17" Ultimate Bandsaw

Unpainted Cast Iron

Protect the unpainted cast iron surfaces on the table by wiping the table clean after every use— this ensures moisture from wood dust does not remain on bare metal surfaces.

Keep tables rust-free with regular applications of products like G96® Gun Treatment, SLIPIT®, or Boeshield® T-9 (see Section 5: Accessories on Page 37 for more details).

Brushes

The bandsaw is equipped with three lower brush- es. The brushes should be checked daily and cleaned when they become dirty. There are adjustment brackets that allow the brushes to be adjusted for bristle wear. Refer to Adjusting Brushes on Page 46 for adjustment details.

Lubrication

Sealed and pre-lubricated ball bearings require no lubrication for the life of the bearings. All bear- ings are standard sizes, and replacements can be purchased from our parts department or a bearing supply store.

Most other moving parts need to be lubricated as needed to maintain smooth function of the bandsaw.

-39-

Image 41
Contents Model G0636X Ultimate Bandsaw Page Table of Contents Contact Info IntroductionForeword Machine Data Sheet G0636X 17 Ultimate Bandsaw Identification Safety Instructions for Machinery G0636X 17 Ultimate Bandsaw Additional Safety Instructions for Bandsaws Circuit Requirements 220V Single-PhaseSetup Safety SetupItems Needed for Setup UnpackingHardware and Tools Qty Crate Contents Figure QtyInventory Hardware Recognition Chart Placement Location Clean UpSite Considerations Floor LoadTo move and place the bandsaw To move and place the bandsaw using wood shimsMoving & Placing Base Unit Mounting to Shop Floor To install the guide post handwheelGuide Post Handwheel Bolting to Concrete FloorsTo center track the blade Blade TrackingTo set the positive stop Positive StopTo connect a dust collection hose Dust CollectionFence To install the fence handleTo test run the machine Test RunTo adjust the upper blade guides Adjusting Blade Guide BearingsTensioning Blade To tension the bandsaw bladeLateral adjustment of blade guides To adjust the upper support bearing Adjusting Support BearingsTo adjust the lower support bearing Aligning Table To align the fence parallel with the miter slot Aligning FenceMiter Gauge Pointer CalibrationTo calibrate the pointer To calibrate the miter gaugeOverview Operation SafetyOperations Guide Post Foot BrakeBlade Lead Fine Tune TrackingTo correct blade lead To skew your fenceTo tilt the table Table TiltTo shift the table To make a 90˚ crosscut RippingCrosscuttingTo make a rip cut Cutting Curves ResawingBlade Information Stacked CutsBlade Length Blade WidthTooth Pitch Tooth StyleBlade Care Blade BreakageMost common causes of blade breakage are Blade ChangesTo remove a blade To replace a bladeReplacement Blades AccessoriesCarbon Steel Replacement Blades for the Model G0636X Timber Wolf Replacement Blades for the Model G0636XH1302 H2347 H1300 H1298 G7984 H0736Maintenance To lubricate the blade tracking knob To lubricate the tension adjustment assem- blyTo lubricate the blade guide rack and pinion To lubricate the trunnions To lubricate the table tilt rack and pinion assemblyMotor & Electrical ServiceTroubleshooting Cutting Operations Symptom Possible Cause Possible SolutionTools Needed Qty Checking Tensioning V-BeltsTo check the V-belts To tension the V-beltTo adjust the tension lever Adjusting TensionReplacing V-Belts LeverTo adjust the brushes Adjusting Wheel Blade BrushesWheel Alignment Components and Hardware Needed QtyDimensions of coplanarity gauge G0636X 17 Ultimate Bandsaw Coplanarity Gauge Electrical Components Power supply terminal boxSee Figure Wiring DiagramBreakdown Parts Description Parts ListPower Cord Support Plate Labels/Cosmetic Parts Warranty and Returns G0636X 17 Ultimate Bandsaw Page Page