Grizzly owner manual Dimensions of coplanarity gauge G0636X 17 Ultimate Bandsaw

Page 49

6.Place your coplanarity gauge up against both wheels in the positions shown in Figure 67.

��

��

��

��

��

��

��

Figure 66. Dimensions of coplanarity gauge.

G0636X 17" Ultimate Bandsaw

	Coplanarity	Gauge Positions
	Gauge	Gauge Positions
	Gauge

Tracking

Knob

Wheels

Adjustment

Hub

Figure 67. Checking for coplanarity.

7.Adjust the tracking knob to get both wheels parallel. If the wheels won’t go parallel to each other, then move the lower wheel at the adjustment hub (Figure 68) so they line up.

Top Tilt

			Side
	Side		Side
	Side		Tilt
	Tilt		Tilt
	Tilt

Bottom Tilt

Figure 68. Lower wheel adjustment control.

8.If the wheels will go parallel but not coplanar, shim the upper wheel out as needed using thin 3⁄4" washers on the shaft behind the wheel.

-47-

Image 49

Contents Model G0636X Ultimate Bandsaw Page Table of Contents Foreword IntroductionContact Info Machine Data Sheet G0636X 17 Ultimate Bandsaw Identification Safety Instructions for Machinery G0636X 17 Ultimate Bandsaw Additional Safety Instructions for Bandsaws Circuit Requirements 220V Single-PhaseSetup Safety SetupItems Needed for Setup UnpackingInventory Crate Contents Figure QtyHardware and Tools Qty Hardware Recognition Chart Placement Location Clean UpSite Considerations Floor LoadMoving & Placing Base Unit To move and place the bandsaw using wood shimsTo move and place the bandsaw Mounting to Shop Floor To install the guide post handwheelGuide Post Handwheel Bolting to Concrete FloorsTo center track the blade Blade TrackingTo set the positive stop Positive StopTo connect a dust collection hose Dust CollectionFence To install the fence handleTo test run the machine Test RunTo adjust the upper blade guides Adjusting Blade Guide BearingsTensioning Blade To tension the bandsaw bladeLateral adjustment of blade guides To adjust the upper support bearing Adjusting Support BearingsTo adjust the lower support bearing Aligning Table To align the fence parallel with the miter slot Aligning FenceMiter Gauge Pointer CalibrationTo calibrate the pointer To calibrate the miter gaugeOperations Operation SafetyOverview Guide Post Foot BrakeBlade Lead Fine Tune TrackingTo correct blade lead To skew your fenceTo shift the table Table TiltTo tilt the table To make a rip cut RippingCrosscuttingTo make a 90˚ crosscut Cutting Curves ResawingBlade Information Stacked CutsBlade Length Blade WidthTooth Pitch Tooth StyleBlade Care Blade BreakageMost common causes of blade breakage are Blade ChangesTo remove a blade To replace a bladeReplacement Blades AccessoriesCarbon Steel Replacement Blades for the Model G0636X Timber Wolf Replacement Blades for the Model G0636XH1302 H2347 H1300 H1298 G7984 H0736Maintenance To lubricate the blade guide rack and pinion To lubricate the tension adjustment assem- blyTo lubricate the blade tracking knob To lubricate the trunnions To lubricate the table tilt rack and pinion assemblyTroubleshooting ServiceMotor & Electrical Cutting Operations Symptom Possible Cause Possible SolutionTools Needed Qty Checking Tensioning V-BeltsTo check the V-belts To tension the V-beltTo adjust the tension lever Adjusting TensionReplacing V-Belts LeverTo adjust the brushes Adjusting Wheel Blade BrushesWheel Alignment Components and Hardware Needed QtyDimensions of coplanarity gauge G0636X 17 Ultimate Bandsaw Coplanarity Gauge Electrical Components Power supply terminal boxSee Figure Wiring DiagramBreakdown Parts Description Parts ListPower Cord Support Plate Labels/Cosmetic Parts Warranty and Returns G0636X 17 Ultimate Bandsaw Page Page