Grizzly G0636X owner manual Labels/Cosmetic Parts

Page 58

Labels/Cosmetic Parts

			317
	300	311
	300	307	318
		307	318
	301	310
	302
	303
	304		309
		308

305

307

		306
REF	PART #	DESCRIPTION

300	P0636X300	MODEL NUMBER LABEL
301	P0636X301	MACHINE ID LABEL
302	PLABEL-11	SAFETY GLASSES LABEL
303	PLABEL-12	READ MANUAL LABEL
304	PLABEL-14	ELECTRICITY LABEL
305	PPAINT-1	GRIZZLY GREEN PAINT
306	PPAINT-11	GREY PUTTY TOUCH UP PAINT
307	PLABEL-20	DONT OPEN LABEL 2"W X 3 5/16"H
308	PLABEL-19	HANDS/BS BLADE LABEL 2" X 3 5/16"H
309	PLABEL-18	UNPLUG BANDSAW LABEL 2" X 3 5/16"H

312

313

314

315

316

304

REF	PART #	DESCRIPTION

310	P0636X310	BLADE ASSEMBLY DIRECTION LABEL
311	G8589	GRIZZLY NAMEPLATE-LARGE
312	P0636X312	TENSION ADJ LABEL
313	P0636X313	TABLE ANGLE SCALE
314	P0636X314	TABLE LOCK LEVER LABEL
315	P0636X315	TABLE TILT HANDWHEEL WARNING LABEL
316	P0636X316	MOTOR LABEL
317	P0636X317	UPPER WHEEL HINGE/STOP BOLT LABEL
318	P0636X318	PATENT LABEL

Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels.

-56-	G0636X 17" Ultimate Bandsaw

Image 58

Contents Model G0636X Ultimate Bandsaw Page Table of Contents Foreword IntroductionContact Info Machine Data Sheet G0636X 17 Ultimate Bandsaw Identification Safety Instructions for Machinery G0636X 17 Ultimate Bandsaw Additional Safety Instructions for Bandsaws 220V Single-Phase Circuit RequirementsItems Needed for Setup SetupSetup Safety UnpackingInventory Crate Contents Figure QtyHardware and Tools Qty Hardware Recognition Chart Site Considerations Clean UpPlacement Location Floor LoadMoving & Placing Base Unit To move and place the bandsaw using wood shimsTo move and place the bandsaw Guide Post Handwheel To install the guide post handwheelMounting to Shop Floor Bolting to Concrete FloorsBlade Tracking To center track the bladePositive Stop To set the positive stopDust Collection To connect a dust collection hoseTo install the fence handle FenceTest Run To test run the machineTensioning Blade Adjusting Blade Guide BearingsTo adjust the upper blade guides To tension the bandsaw bladeLateral adjustment of blade guides Adjusting Support Bearings To adjust the upper support bearingTo adjust the lower support bearing Aligning Table Aligning Fence To align the fence parallel with the miter slotTo calibrate the pointer Pointer CalibrationMiter Gauge To calibrate the miter gaugeOperations Operation SafetyOverview Foot Brake Guide PostTo correct blade lead Fine Tune TrackingBlade Lead To skew your fenceTo shift the table Table TiltTo tilt the table To make a rip cut RippingCrosscuttingTo make a 90˚ crosscut Resawing Cutting CurvesBlade Length Stacked CutsBlade Information Blade WidthBlade Care Tooth StyleTooth Pitch Blade BreakageTo remove a blade Blade ChangesMost common causes of blade breakage are To replace a bladeCarbon Steel Replacement Blades for the Model G0636X AccessoriesReplacement Blades Timber Wolf Replacement Blades for the Model G0636XH2347 H1300 H1298 G7984 H0736 H1302Maintenance To lubricate the blade guide rack and pinion To lubricate the tension adjustment assem- blyTo lubricate the blade tracking knob To lubricate the table tilt rack and pinion assembly To lubricate the trunnionsTroubleshooting ServiceMotor & Electrical Symptom Possible Cause Possible Solution Cutting OperationsTo check the V-belts Checking Tensioning V-BeltsTools Needed Qty To tension the V-beltReplacing V-Belts Adjusting TensionTo adjust the tension lever LeverWheel Alignment Adjusting Wheel Blade BrushesTo adjust the brushes Components and Hardware Needed QtyDimensions of coplanarity gauge G0636X 17 Ultimate Bandsaw Coplanarity Gauge Power supply terminal box Electrical ComponentsWiring Diagram See FigureBreakdown Parts Parts List DescriptionPower Cord Support Plate Labels/Cosmetic Parts Warranty and Returns G0636X 17 Ultimate Bandsaw Page Page