Grizzly G0636X owner manual Coplanarity Gauge

Page 50

9.Figure 69 shows the positions of the wheels when coplanar. When your wheels are copla- nar, reinstall the table, table insert, and pin, readjust the guide blocks and rear support bearings, and close the wheel covers.

10.Finally, check table and fence alignment (see Pages 25 & 26).

Note: The blade may track slightly off-center when the wheels are coplanar. This is natural because the blade will be balanced on the crown of the tire, rather than just in the center of the tire. This will be more noticeable with larger blades.

Coplanar

Parallel, Not

Not Parallel

Adjust

Coplanar

Not Coplanar

Tracking Knob

 

Coplanarity Gauge

Coplanarity

Gauge

Contacts Top

And Bottom of

Both Wheels

Shim Upper

Wheel Out

Adjust

Lower

Hub

Figure 69. Coplanarity diagram.

-48-

G0636X 17" Ultimate Bandsaw

Image 50
Contents Model G0636X Ultimate Bandsaw Page Table of Contents Contact Info IntroductionForeword Machine Data Sheet G0636X 17 Ultimate Bandsaw Identification Safety Instructions for Machinery G0636X 17 Ultimate Bandsaw Additional Safety Instructions for Bandsaws 220V Single-Phase Circuit RequirementsItems Needed for Setup SetupSetup Safety UnpackingHardware and Tools Qty Crate Contents Figure QtyInventory Hardware Recognition Chart Site Considerations Clean UpPlacement Location Floor LoadTo move and place the bandsaw To move and place the bandsaw using wood shimsMoving & Placing Base Unit Guide Post Handwheel To install the guide post handwheelMounting to Shop Floor Bolting to Concrete FloorsBlade Tracking To center track the bladePositive Stop To set the positive stopDust Collection To connect a dust collection hoseTo install the fence handle FenceTest Run To test run the machineTensioning Blade Adjusting Blade Guide BearingsTo adjust the upper blade guides To tension the bandsaw bladeLateral adjustment of blade guides Adjusting Support Bearings To adjust the upper support bearingTo adjust the lower support bearing Aligning Table Aligning Fence To align the fence parallel with the miter slotTo calibrate the pointer Pointer CalibrationMiter Gauge To calibrate the miter gaugeOverview Operation SafetyOperations Foot Brake Guide PostTo correct blade lead Fine Tune TrackingBlade Lead To skew your fenceTo tilt the table Table TiltTo shift the table To make a 90˚ crosscut RippingCrosscuttingTo make a rip cut Resawing Cutting CurvesBlade Length Stacked CutsBlade Information Blade WidthBlade Care Tooth StyleTooth Pitch Blade BreakageTo remove a blade Blade ChangesMost common causes of blade breakage are To replace a bladeCarbon Steel Replacement Blades for the Model G0636X AccessoriesReplacement Blades Timber Wolf Replacement Blades for the Model G0636XH2347 H1300 H1298 G7984 H0736 H1302Maintenance To lubricate the blade tracking knob To lubricate the tension adjustment assem- blyTo lubricate the blade guide rack and pinion To lubricate the table tilt rack and pinion assembly To lubricate the trunnionsMotor & Electrical ServiceTroubleshooting Symptom Possible Cause Possible Solution Cutting OperationsTo check the V-belts Checking Tensioning V-BeltsTools Needed Qty To tension the V-beltReplacing V-Belts Adjusting TensionTo adjust the tension lever LeverWheel Alignment Adjusting Wheel Blade BrushesTo adjust the brushes Components and Hardware Needed QtyDimensions of coplanarity gauge G0636X 17 Ultimate Bandsaw Coplanarity Gauge Power supply terminal box Electrical ComponentsWiring Diagram See FigureBreakdown Parts Parts List DescriptionPower Cord Support Plate Labels/Cosmetic Parts Warranty and Returns G0636X 17 Ultimate Bandsaw Page Page