Grizzly G0636X owner manual Aligning Fence, To align the fence parallel with the miter slot

Page 28

Aligning Fence

To ensure cutting accuracy when the fence is first installed, the fence should be aligned with the

miter slot.

To align the fence parallel with the miter slot:

1.DISCONNECT BANDSAW FROM POWER!

2.Make sure the miter slot is aligned with the bandsaw blade (see Page 25).

3.If the fence is mounted on the left-hand side of the blade, remove it and remount it next to the miter slot.

4.Loosen the two cap screws that secure the rail to the table (Figure 33).

Cap Screws

Figure 33. Cap screws securing rail to table.

5.Adjust the fence face parallel with the edge of the miter slot, as shown in Figure 34.

-26-

Figure 34. Example of fence square with miter

slot.

6.Tighten the two cap screws that secure the rail to the table, being careful not to move the fence.

NOTICE

Adjusting the fence parallel to the miter slot does not guarantee straight cuts. The miter slot may need to be adjusted parallel to the side of the blade. Refer to the "Aligning Table" instructions on Page 25.

G0636X 17" Ultimate Bandsaw

Image 28
Contents Model G0636X Ultimate Bandsaw Page Table of Contents Foreword IntroductionContact Info Machine Data Sheet G0636X 17 Ultimate Bandsaw Identification Safety Instructions for Machinery G0636X 17 Ultimate Bandsaw Additional Safety Instructions for Bandsaws 220V Single-Phase Circuit RequirementsSetup Setup SafetyItems Needed for Setup UnpackingInventory Crate Contents Figure QtyHardware and Tools Qty Hardware Recognition Chart Clean Up Placement LocationSite Considerations Floor LoadMoving & Placing Base Unit To move and place the bandsaw using wood shimsTo move and place the bandsaw To install the guide post handwheel Mounting to Shop FloorGuide Post Handwheel Bolting to Concrete FloorsBlade Tracking To center track the bladePositive Stop To set the positive stopDust Collection To connect a dust collection hoseTo install the fence handle FenceTest Run To test run the machineAdjusting Blade Guide Bearings To adjust the upper blade guidesTensioning Blade To tension the bandsaw bladeLateral adjustment of blade guides Adjusting Support Bearings To adjust the upper support bearingTo adjust the lower support bearing Aligning Table Aligning Fence To align the fence parallel with the miter slotPointer Calibration Miter GaugeTo calibrate the pointer To calibrate the miter gaugeOperations Operation SafetyOverview Foot Brake Guide PostFine Tune Tracking Blade LeadTo correct blade lead To skew your fenceTo shift the table Table TiltTo tilt the table To make a rip cut RippingCrosscuttingTo make a 90˚ crosscut Resawing Cutting CurvesStacked Cuts Blade InformationBlade Length Blade WidthTooth Style Tooth PitchBlade Care Blade BreakageBlade Changes Most common causes of blade breakage areTo remove a blade To replace a bladeAccessories Replacement BladesCarbon Steel Replacement Blades for the Model G0636X Timber Wolf Replacement Blades for the Model G0636XH2347 H1300 H1298 G7984 H0736 H1302Maintenance To lubricate the blade guide rack and pinion To lubricate the tension adjustment assem- blyTo lubricate the blade tracking knob To lubricate the table tilt rack and pinion assembly To lubricate the trunnionsTroubleshooting ServiceMotor & Electrical Symptom Possible Cause Possible Solution Cutting OperationsChecking Tensioning V-Belts Tools Needed QtyTo check the V-belts To tension the V-beltAdjusting Tension To adjust the tension leverReplacing V-Belts LeverAdjusting Wheel Blade Brushes To adjust the brushesWheel Alignment Components and Hardware Needed QtyDimensions of coplanarity gauge G0636X 17 Ultimate Bandsaw Coplanarity Gauge Power supply terminal box Electrical ComponentsWiring Diagram See FigureBreakdown Parts Parts List DescriptionPower Cord Support Plate Labels/Cosmetic Parts Warranty and Returns G0636X 17 Ultimate Bandsaw Page Page