Grizzly G1023SLWX instruction manual Piece Inventory, G1023SL/G1023SLX base unit

Page 14

Piece Inventory

After all the parts have been removed from their containers, you should have:

¥Table Saw Unit (Figure 6)

¥Miter Gauge

¥Extension Wings (2)*

¥Fence Assembly

¥Splitter/Guard Assembly

¥Dust Port

¥Table Insert

¥Dado Insert

¥Cabinet Cover

¥Arbor Wrench

¥Support Shaft

¥Handwheel and Handle

¥Switch Brace

¥Hardware Bag

* The Model G1023SLX comes with only (1) extension wing.

Figure 6. G1023SL/G1023SLX base unit.

Figure 8. G1023SL component layout.

The hardware bag should contain the following:

¥(1) 3mm Allen¨ Wrench

¥(1) 4mm Allen¨ Wrench

¥(1) Flat Head Screw 5Ú16"-18 x 11Ú2"

¥(1) Combo Wrench 5Ú8"

¥(2) Hinge Pins

¥(2) Hex Bolt 5Ú16"-18 x 11Ú2"

¥(2) Hex Bolt 5Ú16"-18 x 1"

¥(3) Hex Nut 5Ú16"-18

¥(7) Flat Washers 5Ú16"

¥(2) Lock Washer 5Ú16"

¥(2) Setscrew 5Ú16"-18 x 3Ú8"

In the event that any nonproprietary parts are missing (e.g. a nut or a washer), we would be glad to replace them; or for the sake of expedien- cy, replacements can be obtained at your local hardware store.

Note: A full component and hardware breakdown of the Shop Fox¨ Classic fence can be found in the manual that accompanies the fence. Those items are not included in this manual.




-12-	G1023SL/G1023SLX Left-Tilting 10'' Table Saw

Image 14

Contents LEFT-TILTING 10 Table SAW Page Table of Contents Safety Safety Instructions For Power ToolsLength AMP Rating Additional Safety Instructions For Table Saws Push Sticks Zero Clearance Table InsertsPush Paddles FeatherboardsCommon Definitions, Terms and Phrases 220V Single-Phase Grounding Circuit RequirementsWiring Extension CordsIntroduction CommentaryUnpacking Piece Inventory G1023SL/G1023SLX base unitClean up Site Considerations Assembly Extension WingsFence SwitchTo mount the switch StepMotor Brace Guard BracketHandwheel Table InsertBlade Guard/Splitter Dust PortSaw Blade Blade splitter square to table Adjustment Bolt Arbor Bracket Blade Tilt AdjustmentsBlade Height Miter Slot to Blade Shim procedure diagram a Blade Alignment To adjust the blade position by moving the trunnionTo adjust the blade position by moving the arbor bracket Rip Fence Miter GaugeOperations Pre-Run CheckTest Run Blade SelectionPlywood blade G1023SL/G1023SLX Left-Tilting 10 Table Saw To make a crosscut using the miter gauge CrosscuttingRipping Do not stand directly behind woodDado Operations To use a dado bladeRabbet Operations To use a dado blade for rabbeting operationsG1023SL/G1023SLX Left-Tilting 10 Table Saw Belt MaintenanceGeneral TablesTo replace the V-belts To adjust V-belt tensionLubrication SDN Type Closure Machine Data Sheet G1023SL/G1023SLX Left-Tilting 10 Table Saw G1023SL/G1023SLX Left-Tilting 10 Table Saw G1023SL/G1023SLX Left-Tilting 10 Table Saw Cabinet Rear Trunnion Bracket Troubleshooting Guide Symptom Possible Cause Corrective ActionG1023SL/G1023SLX Left-Tilting 10 Table Saw Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC BOX BELLINGHAM, WA

Related manuals

Manual 3 pages 44.31 Kb