Grizzly G1023SLX, G1023SLWX instruction manual Rip Fence, Miter Gauge

Page 27

5.Moving the arbor bracket moves the V-belts and pulleys out of alignment, so adjustment of the motor pulley is required. Simply loosen the setscrew in the middle motor groove pul- ley and slowly slide the pulley towards the end of the motor shaft. Once the V-belts are back in alignment, tighten the setscrew securely.

6.Reattach the table, making sure there is ade- quate blade clearance through all blade adjustments. Recheck guard alignment to the blade and to the table top. Adjust as nec- essary and tighten down all the bolts before use.

7.If the blade is still contacting the insert, repeat Steps 1-6. Check all other adjust- ments.

8.Recheck the blade to miter slot adjustments, and adjust as necessary.

Rip Fence

The rip fence included with your Model G1023SL/G1023SLX Left-Tilting 10" Table Saw is designed to provide excellent ripping accuracy when properly adjusted. For complete adjustment procedures, refer to the manual that is included with the fence.

Miter Gauge

To adjust the miter gauge so it is perpendicu- lar to the saw blade:

1.Loosen the lock knob on the miter gauge and place a square against the face of the miter body and the blade.

2.Adjust the miter body until there is no space between the square and the blade. Tighten the lock knob.

3.With the stop link in the up position, loosen the jam nut and adjust the stop screw until it is seated against the stop link. See Figure 30 for part locations.

4.Now loosen the setscrew on the left front side of the miter bar, adjust the pointer to 90¡ and tighten the setscrew.

5.To adjust to 45¡, follow Steps 1-4using an adjustable square set to 45¡.

6.After rotating the miter body from 45¡ to 90¡ and back a few times, double-check your adjustments at both angles to assure that you have accurately set your miter gauge.

The miter bar can be adjusted so that it fits tighter in the miter slot. To do this, turn the adjustment setscrew shown in Figure 30 clockwise. Turn the adjustment setscrew in small increments at a time so you do not over-adjust the miter bar.

Jam Nut

Pointer

 

Stop Link

Adjustment

Stop Screw

Setscrew

Setscrew

 

Figure 30. Miter gauge diagram

G1023SL/G1023SLX Left-Tilting 10'' Table Saw

-25-

Page 26 Page 28
Image 27
Page 26 Page 28
Contents LEFT-TILTING 10 Table SAW Page Table of Contents Safety Instructions For Power Tools SafetyLength AMP Rating Additional Safety Instructions For Table Saws Zero Clearance Table Inserts Push SticksFeatherboards Push PaddlesCommon Definitions, Terms and Phrases Circuit Requirements 220V Single-Phase GroundingExtension Cords WiringCommentary IntroductionUnpacking G1023SL/G1023SLX base unit Piece InventoryClean up Site Considerations Extension Wings AssemblyStep SwitchTo mount the switch FenceGuard Bracket Motor BraceTable Insert HandwheelDust Port Saw BladeBlade Guard/Splitter Blade splitter square to table Adjustment Bolt Arbor Bracket Adjustments Blade HeightBlade Tilt Miter Slot to Blade Shim procedure diagram a To adjust the blade position by moving the trunnion To adjust the blade position by moving the arbor bracketBlade Alignment Miter Gauge Rip FencePre-Run Check OperationsBlade Selection Test RunPlywood blade G1023SL/G1023SLX Left-Tilting 10 Table Saw Crosscutting To make a crosscut using the miter gaugeDo not stand directly behind wood RippingTo use a dado blade Dado OperationsTo use a dado blade for rabbeting operations Rabbet OperationsG1023SL/G1023SLX Left-Tilting 10 Table Saw Tables MaintenanceGeneral BeltTo adjust V-belt tension LubricationTo replace the V-belts SDN Type Closure Machine Data Sheet G1023SL/G1023SLX Left-Tilting 10 Table Saw G1023SL/G1023SLX Left-Tilting 10 Table Saw G1023SL/G1023SLX Left-Tilting 10 Table Saw Cabinet Rear Trunnion Bracket Symptom Possible Cause Corrective Action Troubleshooting GuideG1023SL/G1023SLX Left-Tilting 10 Table Saw Warranty and Returns Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INC
Related manuals
Manual 3 pages 44.31 Kb
Top Page Image Contents