Grizzly G0451 instruction manual Adjusting Replacing Scoring Blade, Scoring blade set

Page 39

Adjusting and

Replacing Scoring

Blade

The scoring blade that is included with the sliding table saw is wedge shaped. The kerf thickness of this style of scoring blade is adjusted by changing the height of the scoring blade. Most replacement scoring blade sets consists of an inner and outer blade with internal shims. The shims are pro- vided so the scoring blade set can match the kerf thickness of the main blade. Figure 59 shows a replacement scoring blade set laid out for identi- fication. For optimum performance, replace the scoring blades when they start to get dull.

Figure 59. Scoring blade set.

To change the scoring blade:

1.Disconnect the saw from the power source!

2.Move the blade tilt to 0˚ (blade 90˚ to table), and raise the scoring blade all the way up.

3.Move the sliding table all the way forward to expose the internal blade guard that covers the blades and riving knife.

4.To remove the scoring blade, use the arbor wrench to remove the arbor nut and arbor flange (see Figure 60). Note—The arbor nut has right-hand threads and loosens by turn- ing counterclockwise.

Figure 60. Removing the scoring blade.

5.Adjust the width of the scoring blade.

—If you are using a tapered scoring blade, complete Step 6, then adjust the kerf as instructed on Page 31 before continuing to Step 7.

—If you are using a stacked scoring blade set, measure the main blade and use the shims to stack the set so the thickness matches the thickness of the main blade.

6.Install the new scoring blade, re-install the arbor flange and the arbor nut, and tighten them against the blade set.

7.Move the orange blade guard back into its original position, next to the blades, and cen- ter the sliding table.

8.Align the scoring blade set to the main blade as described in the “Aligning Scoring Blade Set” instructions on Page 31.

9.Perform a test cut and check for chip out on the underside of the test piece. If there is chip out, make the adjustments necessary to match the kerfs.

G0451 14" Sliding Table Saw

-37-

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Sliding Table SAW Page Table of Contents Accessories Maintenance Introduction ForewordContact Info Machine Data Sheet Identification Blade Elevation Handwheel-AdjustsPage Page Safety Instructions for Machinery SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety Instructions for Table Saws Preventing Kickback Protecting Yourself From KickbackBelow are tips to reduce the likelihood of kickback Glossary Of Terms Circuit Requirements 220/440V 3-PhaseRewiring to Phase Converter GroundingMain Description Qty SET UPSet Up Safety Unpacking Items Needed For Set UpBox 5 Figure Qty InventoryBox 1 Figure Qty Box 4 Figure Qty Crosscut TableBox 7 Figure Qty Box 7 Cont. Figure QtyBox 7 Qty Hardware Recognition Chart Site Considerations Clean UpLifting the saw base unit G0451 14 Sliding Table Saw Moving & Placing Base UnitTools Needed Qty To install the extension tablesExtension Tables Components and Hardware Needed QtyScale To install the scaleRip Fence To install the rip fenceRip fence height adjustment G0451 14 Sliding Table Saw Crosscut Table To install the crosscut tableCrosscut Fence To install the crosscut fenceTo assemble the sliding table components Sliding TableComponents and Hardware Needed Tools NeededMain Blade To install the bladePage Adjusting Scoring Blade Kerf Aligning Scoring Blade SetScale Alignment To connect the dust ports to a dust collection system Dust CollectionTo connect the saw to the power source Power Cord Test RunOperation Safety Operation Tips OperationsPlease follow these tips Every time you use your saw Changing Main Blade Riving Knife Adjustment Scoring blade set Adjusting Replacing Scoring BladeRip cutting with the sliding table Rip CuttingSliding Rip cutting using the traditional table saw techniqueCrosscutting smaller panels G0451 14 Sliding Table Saw CrosscuttingCrosscutting smaller panels Crosscutting using the rip fence as a cut-offCrosscutting full size panels GaugeTo perform a miter cut Miter CuttingG5562-SLIPIT1 Qt. Gel G5563-SLIPIT12 oz Spray AccessoriesG1955-OxiSolvBlade & Bit Cleaner G7895-Citrus DegreaserH4935-Scoring Blade Set H1300 H1298 G7984 H2347 H0736G7581-Superbar G7582-Master Plate H3308-SHOP FOX Push StickG3445-Precision Saw Tool H3771-Blade LocUnpainted Cast Iron MaintenanceCleaning ScheduleGear lubrication LubricationDate Approximate Hours Of Use Maintenance Performed Maintenance LogService About ServiceReplacing Belts Blade Tilt Table mounting bolt access plate G0451 14 Sliding Table Saw Sliding Table Parallel AdjustmentTo square the crosscut fence with the blade Squaring Crosscut Fence to BladeService Log Symptom Possible Cause Possible Solution TroubleshootingLoud repetitious noise coming Electrical Main Motor Contactor Scoring Motor Parts Extension Arm AssemblyStop Bracket Extension Table Assembly Roller Sliding Table Saw Base AssemblyPSB50M Assembly PW04M Flat Washer 10MM Arbor and Dust Hood Assembly Blade Guard Sliding Protect Plate Table Assembly Support Brace Fence Assembly Rotate Shaft Motor Assembly Scoring Flange Blade Adjustment Assembly Free Joint Swing Arm Assembly Nylon Washer M10 X Main Motor Assembly Dust Port Warranty and Returns Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INC

G0451 specifications

The Grizzly G0451 is a highly regarded features-rich jointer and planer combo, designed to meet the needs of both hobbyists and professionals in woodworking. This versatile machine stands out for its precision, durability, and exceptional performance, making it a solid investment for any workshop.

One of the most distinguishing features of the Grizzly G0451 is its powerful 2 HP motor. This robust motor drives the cutter head at 10,000 RPM, allowing for efficient removal of material and ensuring clean, smooth finishes on wood surfaces. The machine can handle stock widths up to 6 inches and features a total thickness capacity of 6 inches, which means you can work on a variety of wood pieces with ease.

The G0451's design includes an easy-to-use height adjustment system that allows users to change the thickness settings quickly and accurately. The precision-machined cast iron table provides a stable work surface that minimizes vibration and maintains alignment, contributing to the machine's overall accuracy. Additionally, the fence system is built to provide reliable support, featuring easy-to-read scales and ample adjustability for various woodworking applications.

Another notable characteristic of this jointer-planer combo is its robust build quality. The heavy-duty construction, combined with premium components, ensures longevity and reliability, a vital consideration for anyone who uses the machine regularly. The G0451 also incorporates advanced safety features, such as an emergency stop switch and anti-kickback fingers, helping to protect operators during use.

In terms of technology, the Grizzly G0451 utilizes a spiral cutter head that significantly reduces noise and enhances cutting efficiency. This innovative design features several staggered razor-sharp blades, which provide a superior cut while minimizing tear-out in delicate woods. The cutter head can be easily replaced when worn, allowing for ongoing maintenance while ensuring the highest quality performance over time.

The overall compact design of the G0451 is well-suited for smaller workshops, providing powerful capabilities without sacrificing much floor space. In summary, the Grizzly G0451 is an exceptional jointer and planer combo that boasts a combination of powerful performance, exceptional build quality, and modern features. Whether you're a seasoned woodworker or just starting, the G0451 presents a compelling solution to your woodworking needs, ultimately delivering professional results with precision and ease.
Top Page Image Contents