Grizzly G0451 Squaring Crosscut Fence to Blade, To square the crosscut fence with the blade

Page 54

9.Slowly make the adjustments to the parallel- ism adjustment bolts (Figure 95) on the end that is closer to the blade.

3.Use the crosscut fence to cut 1⁄2" off of each side of the test piece, then cut side 1 again (make five cuts total).

4.Measure the test piece diagonally from cor- ner-to-corner as shown in Figure 96.

—If both measurements are not within 1⁄16", then the crosscut fence needs to be adjusted. Proceed to Step 6.

—If both measurements are within 1⁄16" then you are finished with this procedure.

Figure 95. Table parallelism adjustment bolts.

10.Repeat Steps 4-9until the gap between the blade and the sliding table is equal.

11.Tighten the jam nuts on the parallel adjust- ment bolts to secure them in place

12.Tighten the table mounting bolts and replace the access plates.

Squaring Crosscut

Fence to Blade

Squaring the crosscut fence to the blade ensures that cuts made with the crosscut fence will be square. This procedure can be done by using a piece of scrap plywood as a test piece and making five test cuts, then adjusting the fence as necessary.

To square the crosscut fence with the blade:

1.Make sure the blade is parallel with the slid- ing table.

2.Prepare the scrap test piece by cutting it to 32" x 32" and number all four sides of the test piece.

-52-

Figure 96. Fence adjustment test piece.

5.Loosen the set screw shown in Figure 97 and rotate the cam to square the crosscut fence.

Adjustment

Cam

Set Screw

Figure 97. Crosscut fence adjustment cam.

6.Tighten the set screw and repeat Step 3-6.

G0451 14" Sliding Table Saw

Page 53 Page 55
Image 54
Page 53 Page 55
Contents Sliding Table SAW Page Table of Contents Accessories Maintenance Introduction ForewordContact Info Machine Data Sheet Blade Elevation Handwheel-Adjusts IdentificationPage Page Safety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety Instructions for Table Saws Preventing Kickback Protecting Yourself From KickbackBelow are tips to reduce the likelihood of kickback Glossary Of Terms 220/440V 3-Phase Circuit RequirementsPhase Converter Grounding Rewiring toMain Items Needed For Set Up SET UPSet Up Safety Unpacking Description QtyBox 4 Figure Qty Crosscut Table InventoryBox 1 Figure Qty Box 5 Figure QtyBox 7 Figure Qty Box 7 Cont. Figure QtyBox 7 Qty Hardware Recognition Chart Clean Up Site ConsiderationsMoving & Placing Base Unit Lifting the saw base unit G0451 14 Sliding Table SawComponents and Hardware Needed Qty To install the extension tablesExtension Tables Tools Needed QtyTo install the scale ScaleTo install the rip fence Rip FenceRip fence height adjustment G0451 14 Sliding Table Saw To install the crosscut table Crosscut TableTo install the crosscut fence Crosscut FenceTools Needed Sliding TableComponents and Hardware Needed To assemble the sliding table componentsTo install the blade Main BladePage Adjusting Scoring Blade Kerf Aligning Scoring Blade SetScale Alignment Dust Collection To connect the dust ports to a dust collection systemPower Cord Test Run To connect the saw to the power sourceOperation Safety Operation Tips OperationsPlease follow these tips Every time you use your saw Changing Main Blade Riving Knife Adjustment Adjusting Replacing Scoring Blade Scoring blade setRip Cutting Rip cutting with the sliding tableRip cutting using the traditional table saw technique SlidingCrosscutting Crosscutting smaller panels G0451 14 Sliding Table SawGauge Crosscutting using the rip fence as a cut-offCrosscutting full size panels Crosscutting smaller panelsMiter Cutting To perform a miter cutG7895-Citrus Degreaser AccessoriesG1955-OxiSolvBlade & Bit Cleaner G5562-SLIPIT1 Qt. Gel G5563-SLIPIT12 oz SprayH1300 H1298 G7984 H2347 H0736 H4935-Scoring Blade SetH3771-Blade Loc H3308-SHOP FOX Push StickG3445-Precision Saw Tool G7581-Superbar G7582-Master PlateSchedule MaintenanceCleaning Unpainted Cast IronLubrication Gear lubricationMaintenance Log Date Approximate Hours Of Use Maintenance PerformedService About ServiceReplacing Belts Blade Tilt Sliding Table Parallel Adjustment Table mounting bolt access plate G0451 14 Sliding Table SawSquaring Crosscut Fence to Blade To square the crosscut fence with the bladeService Log Troubleshooting Symptom Possible Cause Possible SolutionLoud repetitious noise coming Electrical Main Motor Contactor Scoring Motor Extension Arm Assembly PartsStop Bracket Extension Table Assembly Roller Base Assembly Sliding Table SawPSB50M Assembly PW04M Flat Washer 10MM Arbor and Dust Hood Assembly Blade Guard Sliding Protect Plate Table Assembly Support Brace Fence Assembly Rotate Shaft Motor Assembly Scoring Flange Blade Adjustment Assembly Free Joint Swing Arm Assembly Nylon Washer M10 X Main Motor Assembly Dust Port Warranty and Returns Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WA

G0451 specifications

The Grizzly G0451 is a highly regarded features-rich jointer and planer combo, designed to meet the needs of both hobbyists and professionals in woodworking. This versatile machine stands out for its precision, durability, and exceptional performance, making it a solid investment for any workshop.

One of the most distinguishing features of the Grizzly G0451 is its powerful 2 HP motor. This robust motor drives the cutter head at 10,000 RPM, allowing for efficient removal of material and ensuring clean, smooth finishes on wood surfaces. The machine can handle stock widths up to 6 inches and features a total thickness capacity of 6 inches, which means you can work on a variety of wood pieces with ease.

The G0451's design includes an easy-to-use height adjustment system that allows users to change the thickness settings quickly and accurately. The precision-machined cast iron table provides a stable work surface that minimizes vibration and maintains alignment, contributing to the machine's overall accuracy. Additionally, the fence system is built to provide reliable support, featuring easy-to-read scales and ample adjustability for various woodworking applications.

Another notable characteristic of this jointer-planer combo is its robust build quality. The heavy-duty construction, combined with premium components, ensures longevity and reliability, a vital consideration for anyone who uses the machine regularly. The G0451 also incorporates advanced safety features, such as an emergency stop switch and anti-kickback fingers, helping to protect operators during use.

In terms of technology, the Grizzly G0451 utilizes a spiral cutter head that significantly reduces noise and enhances cutting efficiency. This innovative design features several staggered razor-sharp blades, which provide a superior cut while minimizing tear-out in delicate woods. The cutter head can be easily replaced when worn, allowing for ongoing maintenance while ensuring the highest quality performance over time.

The overall compact design of the G0451 is well-suited for smaller workshops, providing powerful capabilities without sacrificing much floor space. In summary, the Grizzly G0451 is an exceptional jointer and planer combo that boasts a combination of powerful performance, exceptional build quality, and modern features. Whether you're a seasoned woodworker or just starting, the G0451 presents a compelling solution to your woodworking needs, ultimately delivering professional results with precision and ease.
Top Page Image Contents