Grizzly G0451 instruction manual Power Cord Test Run, To connect the saw to the power source

Page 35

Power Cord

Test Run

 

 

 

 

 

 

Before installing the power cord, read through Section 2: Circuit Requirements to check that your setup follows the safety and circuit require- ments, and the power cord and plug that you have chosen meet the requirements for this machine.

Components and Hardware Needed:

Qty

Power Cord

1

Tools Needed:

 

Phillips Head Screwdriver

1

To connect the saw to the power source:

1.Open the terminal box shown in Figure 54.

R S T Ground

Figure 54. Main terminal box.

2.Feed the power cord through the strain relief on the bottom of the control panel and connect the cord to the terminals shown in Figure 54, then close the terminal box.

Note—When using a phase converter, connect the manufactured power leg to the S terminal. The S terminal can handle power fluctuation because it is wired directly to the motor. The other wires connect to the transformer and must be consistent to prevent damage.

3.Shut off the main power at the power source circuit breaker and install the cord to the disconnect switch.

Now that the machine is connected to the power source, it is important to perform a test run to make sure all the controls are working properly.

Before starting the saw, make sure you have performed the preceding assembly and adjustment instructions, and you have read through the rest of the manual and are familiar with the various functions and safety issues associated with this machine. Failure to follow this warning could result in serious personal injury or even death!

To test run the saw:

1.Put on safety glasses and make sure any bystanders are out of the way and also wear- ing safety glasses.

2.Insert the key into the control panel and turn it clockwise.

3.Rotate both of the red EMERGENCY STOP buttons until they spring up.

4.Press the main blade button then press the scoring blade button.

—If any problems occur, press the EMERGENCY STOP button.

—If the main blade is rotating in a counter- clockwise direction, disconnect the saw from power and exchange wires R & T in the terminal box.

—Investigate and correct the problem before operating the machine further. If you need help, refer to the Troubleshooting section in the back of this manual or contact our Service Department at (570) 546-9663.

G0451 14" Sliding Table Saw

-33-

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Sliding Table SAW Page Table of Contents Accessories Maintenance Contact Info IntroductionForeword Machine Data Sheet Identification Blade Elevation Handwheel-AdjustsPage Page Safety Instructions for Machinery SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety Instructions for Table Saws Below are tips to reduce the likelihood of kickback Preventing KickbackProtecting Yourself From Kickback Glossary Of Terms Circuit Requirements 220/440V 3-PhaseRewiring to Phase Converter GroundingMain Description Qty SET UPSet Up Safety Unpacking Items Needed For Set UpBox 5 Figure Qty InventoryBox 1 Figure Qty Box 4 Figure Qty Crosscut TableBox 7 Qty Box 7 Figure QtyBox 7 Cont. Figure Qty Hardware Recognition Chart Site Considerations Clean UpLifting the saw base unit G0451 14 Sliding Table Saw Moving & Placing Base UnitTools Needed Qty To install the extension tablesExtension Tables Components and Hardware Needed QtyScale To install the scaleRip Fence To install the rip fenceRip fence height adjustment G0451 14 Sliding Table Saw Crosscut Table To install the crosscut tableCrosscut Fence To install the crosscut fenceTo assemble the sliding table components Sliding TableComponents and Hardware Needed Tools NeededMain Blade To install the bladePage Scale Alignment Adjusting Scoring Blade KerfAligning Scoring Blade Set To connect the dust ports to a dust collection system Dust CollectionTo connect the saw to the power source Power Cord Test RunPlease follow these tips Every time you use your saw Operation Safety Operation TipsOperations Changing Main Blade Riving Knife Adjustment Scoring blade set Adjusting Replacing Scoring BladeRip cutting with the sliding table Rip CuttingSliding Rip cutting using the traditional table saw techniqueCrosscutting smaller panels G0451 14 Sliding Table Saw CrosscuttingCrosscutting smaller panels Crosscutting using the rip fence as a cut-offCrosscutting full size panels GaugeTo perform a miter cut Miter CuttingG5562-SLIPIT1 Qt. Gel G5563-SLIPIT12 oz Spray AccessoriesG1955-OxiSolvBlade & Bit Cleaner G7895-Citrus DegreaserH4935-Scoring Blade Set H1300 H1298 G7984 H2347 H0736G7581-Superbar G7582-Master Plate H3308-SHOP FOX Push StickG3445-Precision Saw Tool H3771-Blade LocUnpainted Cast Iron MaintenanceCleaning ScheduleGear lubrication LubricationDate Approximate Hours Of Use Maintenance Performed Maintenance LogReplacing Belts ServiceAbout Service Blade Tilt Table mounting bolt access plate G0451 14 Sliding Table Saw Sliding Table Parallel AdjustmentTo square the crosscut fence with the blade Squaring Crosscut Fence to BladeService Log Symptom Possible Cause Possible Solution TroubleshootingLoud repetitious noise coming Electrical Main Motor Contactor Scoring Motor Parts Extension Arm AssemblyStop Bracket Extension Table Assembly Roller Sliding Table Saw Base AssemblyPSB50M Assembly PW04M Flat Washer 10MM Arbor and Dust Hood Assembly Blade Guard Sliding Protect Plate Table Assembly Support Brace Fence Assembly Rotate Shaft Motor Assembly Scoring Flange Blade Adjustment Assembly Free Joint Swing Arm Assembly Nylon Washer M10 X Main Motor Assembly Dust Port Warranty and Returns Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INC

G0451 specifications

The Grizzly G0451 is a highly regarded features-rich jointer and planer combo, designed to meet the needs of both hobbyists and professionals in woodworking. This versatile machine stands out for its precision, durability, and exceptional performance, making it a solid investment for any workshop.

One of the most distinguishing features of the Grizzly G0451 is its powerful 2 HP motor. This robust motor drives the cutter head at 10,000 RPM, allowing for efficient removal of material and ensuring clean, smooth finishes on wood surfaces. The machine can handle stock widths up to 6 inches and features a total thickness capacity of 6 inches, which means you can work on a variety of wood pieces with ease.

The G0451's design includes an easy-to-use height adjustment system that allows users to change the thickness settings quickly and accurately. The precision-machined cast iron table provides a stable work surface that minimizes vibration and maintains alignment, contributing to the machine's overall accuracy. Additionally, the fence system is built to provide reliable support, featuring easy-to-read scales and ample adjustability for various woodworking applications.

Another notable characteristic of this jointer-planer combo is its robust build quality. The heavy-duty construction, combined with premium components, ensures longevity and reliability, a vital consideration for anyone who uses the machine regularly. The G0451 also incorporates advanced safety features, such as an emergency stop switch and anti-kickback fingers, helping to protect operators during use.

In terms of technology, the Grizzly G0451 utilizes a spiral cutter head that significantly reduces noise and enhances cutting efficiency. This innovative design features several staggered razor-sharp blades, which provide a superior cut while minimizing tear-out in delicate woods. The cutter head can be easily replaced when worn, allowing for ongoing maintenance while ensuring the highest quality performance over time.

The overall compact design of the G0451 is well-suited for smaller workshops, providing powerful capabilities without sacrificing much floor space. In summary, the Grizzly G0451 is an exceptional jointer and planer combo that boasts a combination of powerful performance, exceptional build quality, and modern features. Whether you're a seasoned woodworker or just starting, the G0451 presents a compelling solution to your woodworking needs, ultimately delivering professional results with precision and ease.
Top Page Image Contents