Woodstock W1819/W1820 manual EXiifn$I`g8lo`c`Xip =\eZ\ Glj9cfZb

FG<I8K@FEJ

	Df[\cN(/(0&N(/)'D]^%J`eZ\()&('
EXiifn$I`g8lo`c`Xip		3⁄4"
=\eZ\Glj_9cfZb	Length	Hardwood
	of Fence	1⁄2"
There are designs for hundreds of specialty jigs that can		Plywood
be found in books, trade magazines, and the internet.	3"
These types of jigs can greatly improve the safety and
consistentcy of cuts. They are particularly useful during		Length
production runs when dozens or hundreds of the same
		of Fence
type of cut need to be made.
The narrow-rip auxiliarly fence and push block system	51⁄4"
shown in this section is an example of a specialty jig that	=`^li\/)% Auxiliary fence dimensions.
can be made to increase the safety of very narrow rip
cuts.
DXb`e^XEXiifn$I`gGlj_9cfZb]fiXe	Pilot Holes	3⁄4" Hardwood
		1⁄2" Plywood
8lo`c`Xip=\eZ\
Materials for Narrow-Rip Push Block & Auxiliary Fence
Hardwood 3⁄4" x 3" x Length of Fence .......................1
Plywood 1⁄2" x 51/4" x Length of Fence .....................1
Plywood 1⁄2" x 10" x 5"-9" .....................................1		Completed
Plywood 1⁄2" x 15" x 53⁄8" ......................................1
Wood Screws #8 x 11/4" ............................ As Needed		Fence
KfdXb\XeXiifn$i`gglj_YcfZb#[fk_\j\jk\gj1	=`^li\83%Location of pilot holes.
(% Cut a piece of 1⁄2" thick plywood 51⁄4" wide and as	55⁄8"
long as your table saw fence; cut a piece of 3⁄4"
thick hardwood 3" wide and as long as your table	15"
saw fence, as shown in =`^li\/).	21⁄2"	Handle
Efk\1 N\i\Zfdd\e[Zlkk`e^k_\_Xi[nff[YfXi[	3⁄8"
	51⁄4"	Lip
fm\ij`q\#k_\eaf`ek`e^Xe[gcXe`e^`kkfk_\Zfii\Zk
j`q\kfdXb\jli\k_\YfXi[`jjhlXi\Xe[]cXk%Fecp	121⁄2"	3⁄8"
lj\]lie`kli\$^iX[\gcpnff[fib`ce$[i`\[_Xi[nff[		21⁄2"
kfgi\m\eknXig`e^%		3⁄8"
)% Pre-drill and countersink eight pilot holes 3⁄8" from	=`^li\/+% Push block dimensions and
the bottom of the 3" wide board, as shown in =`^li\	construction.
83, then fasten the 51⁄4" and 3" wide boards with
eight #8 x 11⁄4" wood screws.

+% Using the 1⁄2" material you used in the previous steps, cut out pieces for the push block per the dimensions shown in =`^li\/+; for the handle, cut a piece 10" long by 5"–9" high and shape it as desired to fit in your hand.

,% Attach the handle to the base with #8 x 11⁄4" wood screws, attach the lip to the base with cyanoacrylate type wood glue.

-60-