Agilent Technologies E9300 manual 0C to +55C

Page 34

E9300/1/4/A Power Sensor Specifications

Maximum SWR

(0°C to +55°C)

	Frequency	SWR


E9300A	10 MHz to 30 MHz	1.21
	30 MHz to 2 GHz	1.15

	2 GHz to 14 GHz	1.20

	14 GHz to 16 GHz	1.23

	16 GHz to 18 GHz	1.27

E9301A	10 MHz to 30 MHz	1.21
	30 MHz to 2 GHz	1.15

	2 GHz to 6 GHz	1.20

E9304A	9 kHz to 2 GHz	1.15
	2 GHz to 6 GHz	1.20

SWR
1.20
1.15
1.10
1.05
1.00
0	2	4	6	8	10	12	14	16	18	GHz

Figure 9 Typical SWR 10 MHz to 18 GHz (25°C ± 10°C)

34

Image 34

Contents Operating and Service Guide Copyright 1999 Agilent Technologies Legal Information WarrantyCertification Limitation of Warranty Exclusive RemediesGeneral Safety Information Sound EmissionPower Meter Front Panel Operation SafetyConventions Sensors Covered by Manual DocumentationRelated Publications Documentation Table of Contents Standing Wave Ratio SWR and Reflection Coefficient Rho Per Introduction Typical HP E-series E9300 power sensors Power Meter Requirements General InformationAgilent E-Series E9300 Power Sensors in Detail Simplified Block Diagram of Diode Pair/Attenuator/Diode PairGeneral Information Getting Started Checking Power Meter Firmware and DSP RevisionInitial Inspection Interconnections and Calibration Specifications Making Measurements What You’ll Find This Chapter Power Meter Configuration Changes Auto-averaging SettingsMeasuring Spread Spectrum and Multitone Signals Spread Spectrum SignalCdma Signal Measurements Cdma IS-95A 9Ch FwdMultitone Signal Measurements 90 % Frequency GHz Typical Lower Range Calibration FactorPower Meter and Sensor Operation Measuring Tdma SignalsAchieving Stable Results with Tdma Signals Achieving Stable Results with GSM Signals Input Settings , MoreElectromagnetic Compatibility EMC Measurements Setting the Range Measurement Accuracy and SpeedMeasurement Considerations AccuracySpeed and Averaging SummarySpecifications and Characteristics Sensor Low Power Path High Power Path IntroductionConnector Type E9300/1/4/A Power Sensor SpecificationsMaximum SWR 0C to +55C Maximum Power Maximum DC VoltagePower Linearity ± 2.5%Typical Power Linearity at 25C, after zero Additional Power Switching Point Zero Set Zero Drift Measurement NoiseSettling Time Time E4418B E4419BX2 Mode Calibration Factor and Reflection CoefficientCal Factor Uncertainty General E9300/1B and H Power Sensor Specifications Frequency RangeE9300B Typical SWR 25C ± 10C E9300H Typical SWR 10 MHz to 18 GHz 25C ± 10C Maximum Power Sensor To 35 C To 55 C GHz E9300/1B To 0 dBm To 10 dBm 10 to 20 dBm 20 to 26 dBm For larger changes refer to the following table E9300/1H DBm to 0 dBm +44 +30 dBm E9300/1B Conditions Zero Set Zero Drift2 Measurement Settling Time Typical Cal Factor Uncertainty Low Power Path Cal Factor Uncertainty High Power Path References Storage and Shipment EnvironmentE9300/1B and H Power Sensor Specifications Service Cleaning Connector CleaningPerformance Test Frequency System Rho Actual Maximum Uncertainty MeasurementPerformance Test Replaceable Parts Is the illustrated parts breakdown IPB that identifies allIllustrated Parts Break down Reference Agilent Part Qty Description Designation Number LABEL, ID E9301B Service Principles of OperationDisassembly Procedure TroubleshootingRepair of Defective Sensor Reassembly Procedure Removing Power Sensor ShellSales and Service Offices Asia PacificEurope