Sears 113.2433 manual Table Trunnion, Upper Blade, Guide BAR Lock Screw

Page 12

assembly

INSTALLING TABLE

Apply a coat of automobile wax to the table.

1.Place the table on the band saw so that the two trunnion

pins and the table lock bolt go through the slot tn the trunnion.

2.Find the 1-1/8" din. flat washer, a sleeve 11/16" long,

the trunnion lock nut and the table lock handle from among the loose parts.

3.Hold the head of the table lock bolt inside the band saw

with your left hand and oul the 1-1/8" din. flat washer, the sleeve, and the handle on the bolt.

4.Screw the nut on the. bolt and tighten it wit_ the handle while the table is in a horizontal position.

TABLE TRUNNION

TABLE LOCK BOLT TABLE LOCK HANDLE

__TENSION

_

i"_'-_"

I

STUD

INSTALLING THE BLADE

,"__POINTER

Find the blade tension knob among the loose parts. Put a dab of grease or vaseline on the end of the knob and screw it on the tension stud. Screw it on only a few turns, just enough to start moving the pointer.

2.Loosen the two mounting screws and remove the blade Hard.

GUIDE BAR LOCK SCREW

GUIDE BAR

3.Loosen the guide bar lock screw and position the upper

guide assembly approximately three inches above the table as shown and tighten the lock screw.

UPPER BLADE.

GUIDE ASSEMBLY

12

Image 12

Contents Save This Manuat For Future Reference SAW onlySAW with Legs Motor Know Your Power Tool Keep Guards in PlaceAvoid Dangerous Environment Keep Children AwayPAG E LocationProtection Eyes, Hands, Face, Ears, Body Allow Tool to Stop Before Adjusting Belt Drive Front of the Band SAW/SANDER and Front of the Blade GuardGerous Wear YourContacting the SAW Blade Volts Catalog noThis Prong Prong Receptacle AdapterUnpackmn g and checking contents Assembling Steel Legs For MountingABC Support HEX NUT LEG SCR EWINSTALLING MOTOR, PULLEY, V-BELT Belt GuardsLE FT Foot \ Right FootHUB SET Screw KEYPulley Lockwasher Flat Washer Small 2-9/2 DIA, Motor Pulley SetscrewWrench Pulley FlushInstalling Sawdust Elbow SELF-THR Eading Screw Clamp Sawdust Elbow Rubber GasketTable Trunnion Upper BladeGuide BAR Lock Screw Guide BARUpper Thrust Bearing Setscrew Wrench SetscrewsTHRUSTBEARIN!i tl / Upper Thrust Bearing Lower Thrust BearingArms Length ScrewPointer Blade Centered On Tires Both WheelsAdjusting the Table Start of assembly section on pg for checking methodKnob ApproxON-OFF Switch For Your OWN SafetyLock Switch RkkOutlet TENS,ONAUST,NGK.OB--GUIDE BAR Lock ScrewInside Lower Knob Not ShownGuide BAR Setscrew Wrench BAR CombinationSquare Anding BeltSanding Platen Lockwasher PlateBasic Band SAW/SANDER Operation SawingBlade StZEGeneral Maintenance AccessoriesYour Band SAW RecommendedProbable Cause RemedyTrouble Cause RemedyTrouble Shootng TroubleProbable Cause RemedyCraftsman Inch Band SAW/SANDER Model 113.243311Parts LiSTDescription IkeypartFor Wiring Diagram Craftsman 12-INCH Band SAW/SANDER, Model 113.243300See 12 \KEY Part NO. no Kepart NonoDescr Iption Suppued WiTH Model 113.243311 only Hardware for Mounting Tool & MotorSupplied WiTH Model 113.243311 only ThreadMotor Connections Strain ReliefPage Page Model no