Sears 113.2433 manual Basic Band SAW/SANDER Operation, Sawing, Blade, StZE, Sanding

Page 20

basic band saw/sander operation

BASIC BAND SAW/SANDER OPERATION

A band saw is basically a "curve cutting" machine. It is no_ capable of doing inside cutting.

Your Craftsman Band Saw/Sander is no_ only capable of the usual band saw operations, out it can he converted into a sander as well. You can finish wood, certain compositions and plastics and non-ferrous metals.

It is also used for stra ght-line cutting operations such as

crosscutting, ripping, mitering, beveling, compound cutting, and resawing.

SAWING

WARNING: ADJUST THE UPPER GUIDES TO CLEAR THE WORKPIECE.

1.Use both hands while feeding the work into the blade. Hold the workpiece firmly against the table. Use gentle pressure, and do not force the work, but allow the blade to cut.

2.The smallest diameter that can be cut out is determined by the width of the blade. For example, a 1/4" wide

blade will cut a minimum diameter of approximately

1-1/2". CSee Chart)

BLADE SELECTION GUIDE FOR MINIMUM CIRCLE CUTTING

BLADE

1 "

3"

I"

3"

1"

StZE

 

16

4

8

 

SANDING

The sanding belt cuts very rapidly. Practice with some scraps of wood first before you attempt to sand your actual workpiece.

1.Press the workpiece gently against the sanding belt, and keep moving it until the edge is smooth.

20

Image 20
Contents SAW with Legs Motor Save This Manuat For Future ReferenceSAW only Know Your Power Tool Keep Guards in PlaceAvoid Dangerous Environment Keep Children AwayProtection Eyes, Hands, Face, Ears, Body PAG ELocation Allow Tool to Stop Before Adjusting Belt Drive Front of the Band SAW/SANDER and Front of the Blade GuardGerous Wear YourContacting the SAW Blade Volts Catalog noThis Prong Prong Receptacle AdapterUnpackmn g and checking contents Assembling Steel Legs For MountingABC Support HEX NUT LEG SCR EWINSTALLING MOTOR, PULLEY, V-BELT Belt GuardsLE FT Foot \ Right FootPulley Lockwasher Flat Washer HUB SET ScrewKEY Small 2-9/2 DIA, Motor Pulley SetscrewWrench Pulley FlushInstalling Sawdust Elbow SELF-THR Eading Screw Clamp Sawdust Elbow Rubber GasketTable Trunnion Upper BladeGuide BAR Lock Screw Guide BARUpper Thrust Bearing Setscrew Wrench SetscrewsTHRUSTBEARIN!i tl / Upper Thrust Bearing Lower Thrust BearingArms Length ScrewPointer Blade Centered On Tires Both WheelsAdjusting the Table Start of assembly section on pg for checking methodKnob ApproxON-OFF Switch For Your OWN SafetyLock Switch RkkOutlet TENS,ONAUST,NGK.OB--GUIDE BAR Lock ScrewInside Lower Knob Not ShownSquare Guide BARSetscrew Wrench BAR Combination Anding BeltSanding Platen Lockwasher PlateBasic Band SAW/SANDER Operation SawingBlade StZEGeneral Maintenance AccessoriesYour Band SAW RecommendedProbable Cause RemedyTrouble Cause RemedyTrouble Shootng TroubleProbable Cause RemedyCraftsman Inch Band SAW/SANDER Model 113.243311Parts LiSTDescription IkeypartFor Wiring Diagram Craftsman 12-INCH Band SAW/SANDER, Model 113.243300See 12 \Descr Iption KEY Part NO. noKepart Nono Suppued WiTH Model 113.243311 only Hardware for Mounting Tool & MotorSupplied WiTH Model 113.243311 only ThreadMotor Connections Strain ReliefPage Page Model no