Sears 113.2433 manual Front of the Band SAW/SANDER and Front of the Blade Guard, Gerous, Wear Your

Page 4

additional safety instructions

for band saw/sander

WARNING: THE 5" BAND SAW PULLEY AND THE 2-I/2" MOTOR PULLEY FURNISHED, WILL RUN THE

BLADE AT APPROXIMATELY 900 RPM (OR 2700 FEET PER MINUTE) WHEN USED WiTH A 1725 RP_

MOTOR. NEVER SUBSTITUTE THESE PULLEYS TO iNCREASE THIS SPEED BECAUSE IT COULD BE DAN-

GEROUS.

WARNING: DO NOT ALLOW FAMiLIARiTY (GAINED

FROM FREQUENT USE OF YOUR BAND SAW) TO BECOME COMMONPLACE. ALWAYS REMEMBER THAT A CARELESS FRACTION OF A SECOND iS SUFFI-

CIENT TO iNFLICT SEVERE iNJURY.

WEAR YOUR

The operation of any power tOOl can result in foreign

objects being thrown into the eyes, which can result in severe eye aamage. Always wear safety goggles complying with ANSi Z87.1 (shewn on Package} before commencing power tool operation. Safety Goggles are available at Sears

retail or catalog stores.

READ AND FOLLOW THE INSTRUCTIONS APPEARING ON THE iNSTRUCTiON PLATE ON

THE FRONT OF THE BAND SAW/SANDER AND FRONT OF THE BLADE GUARD.

DANGER

ALLOW

TOOL TO

STOP

BEFORE

ADJUSTING

_ BELT DRIVE

BA D SAW- SA DE

4

Image 4

Contents SAW only Save This Manuat For Future ReferenceSAW with Legs Motor Know Your Power Tool Keep Guards in PlaceAvoid Dangerous Environment Keep Children AwayLocation PAG EProtection Eyes, Hands, Face, Ears, Body Allow Tool to Stop Before Adjusting Belt Drive Front of the Band SAW/SANDER and Front of the Blade GuardGerous Wear YourContacting the SAW Blade Volts Catalog noThis Prong Prong Receptacle AdapterUnpackmn g and checking contents Assembling Steel Legs For MountingABC Support HEX NUT LEG SCR EWINSTALLING MOTOR, PULLEY, V-BELT Belt GuardsLE FT Foot \ Right FootKEY HUB SET ScrewPulley Lockwasher Flat Washer Small 2-9/2 DIA, Motor Pulley SetscrewWrench Pulley FlushInstalling Sawdust Elbow SELF-THR Eading Screw Clamp Sawdust Elbow Rubber GasketTable Trunnion Upper BladeGuide BAR Lock Screw Guide BARUpper Thrust Bearing Setscrew Wrench SetscrewsTHRUSTBEARIN!i tl / Upper Thrust Bearing Lower Thrust BearingArms Length ScrewPointer Blade Centered On Tires Both WheelsAdjusting the Table Start of assembly section on pg for checking methodKnob ApproxON-OFF Switch For Your OWN SafetyLock Switch RkkOutlet TENS,ONAUST,NGK.OB--GUIDE BAR Lock ScrewInside Lower Knob Not ShownSetscrew Wrench BAR Combination Guide BARSquare Anding BeltSanding Platen Lockwasher PlateBasic Band SAW/SANDER Operation SawingBlade StZEGeneral Maintenance AccessoriesYour Band SAW RecommendedProbable Cause RemedyTrouble Cause RemedyTrouble Shootng TroubleProbable Cause RemedyCraftsman Inch Band SAW/SANDER Model 113.243311Parts LiSTDescription IkeypartFor Wiring Diagram Craftsman 12-INCH Band SAW/SANDER, Model 113.243300See 12 \Kepart Nono KEY Part NO. noDescr Iption Suppued WiTH Model 113.243311 only Hardware for Mounting Tool & MotorSupplied WiTH Model 113.243311 only ThreadMotor Connections Strain ReliefPage Page Model no