Sears 113.2433 Outlet, TENS,ONAUST,NGK.OB--GUIDE BAR Lock Screw, Inside, Lower Knob Not Shown

Page 17

geffing to know your band saw/sander

2

8

/--TENS,ONAUST,NGK.OB--GUIDE BAR LOCK SCREW

COVER.ETAININGCL,P"\3

\

TENSION SCALE

(Inside)

CORD

OUTLET

"7 THRUST BEARING

ADJ. KNOB

(Lower Knob

Not Shown)

TI LT LOCK

HANDLE

SAW PULLEY

FRONT

1.ADJUSTMENT DIAGRAMS . . . Help you to become familiar with the adjustments,

2.TENSION ADJUSTMENT KNOB . . . Tightening the knob will increase the tension on the blade. Loosening it will decrease the tension.

3.TENSION SCALES... The fractional markings indicate the correct blade tension for various widths of blades.

For example, when installing a 1/4" wide blade, tighten the tension knob until the pointer is pointing to the 1/4

marking.

4.TABLE TILTING . . . Loosen the table lock handle, tilt the table to the desired angle and tighten the lock handle. To return the table to the 90 ° position, tilt it until the 90 ° stop screw rests on the frame, then tighten the lock handle.

BLADEGUIDE

ADJ. KNOB

(Lower Knob Not Shown)

BA CK

5.BLADE GUIDE ADJUSTMENT . - . Turning the knob moves the guides in or out for various widths of blades.

6.LATERAL BLADE GUIDE ADJUSTMENT .... The guides can be adjusted sideways and locked in position by the setscrews.

7.BLADE THRUST BEARING ADJUSTMENT . . . Turn- ing the knob moves the thrust bearings in or out for various widths of blades.

8.GUIDE BAR LOCK SCREW... The upper blade guides

should just clear the workpiece while cutting. Always adjust the guides before turning on the band saw and lock the guide bar by tightening the thumb screw.

17

Image 17
Contents SAW with Legs Motor Save This Manuat For Future ReferenceSAW only Keep Guards in Place Know Your Power ToolAvoid Dangerous Environment Keep Children AwayProtection Eyes, Hands, Face, Ears, Body PAG ELocation Front of the Band SAW/SANDER and Front of the Blade Guard Allow Tool to Stop Before Adjusting Belt DriveGerous Wear YourVolts Catalog no Contacting the SAW BladeThis Prong Prong Receptacle AdapterUnpackmn g and checking contents For Mounting Assembling Steel LegsABC Support HEX NUT LEG SCR EWBelt Guards INSTALLING MOTOR, PULLEY, V-BELTLE FT Foot \ Right FootPulley Lockwasher Flat Washer HUB SET ScrewKEY Setscrew Small 2-9/2 DIA, Motor PulleyWrench Pulley FlushSELF-THR Eading Screw Clamp Sawdust Elbow Rubber Gasket Installing Sawdust ElbowUpper Blade Table TrunnionGuide BAR Lock Screw Guide BARSetscrews Upper Thrust Bearing Setscrew WrenchTHRUSTBEARIN!i tl / Upper Thrust Bearing Lower Thrust BearingScrew Arms LengthPointer Blade Centered On Tires Both WheelsStart of assembly section on pg for checking method Adjusting the TableKnob ApproxFor Your OWN Safety ON-OFF SwitchLock Switch RkkTENS,ONAUST,NGK.OB--GUIDE BAR Lock Screw OutletInside Lower Knob Not ShownSquare Guide BARSetscrew Wrench BAR Combination Belt AndingSanding Platen Lockwasher PlateSawing Basic Band SAW/SANDER OperationBlade StZEAccessories General MaintenanceYour Band SAW RecommendedRemedy Probable CauseTrouble Cause RemedyTrouble Trouble ShootngProbable Cause RemedyModel 113.243311 Craftsman Inch Band SAW/SANDERLiST PartsDescription IkeypartCraftsman 12-INCH Band SAW/SANDER, Model 113.243300 For Wiring DiagramSee 12 \Descr Iption KEY Part NO. noKepart Nono Hardware for Mounting Tool & Motor Suppued WiTH Model 113.243311 onlyThread Supplied WiTH Model 113.243311 onlyMotor Connections Strain ReliefPage Page Model no