Sears 113.2433 manual Installing Motor, Pulley, V-Belt, Belt Guards, LE FT Foot, Right Foot

Page 8

assembly

MOUNTING BAND SAW/SANDER ON LEG SET

NOTE: For illustrative purposes, the Band Saw is shown mounted on the Craftsman Catalog No. 9-22236 Steel *Leg Set. This Leg Set is included with Model No. 113.243311.

1.Remove the Band Saw cover by applying gentle side

pressure on the spring tabs and release the top portion of the cover by pulling it away from the frame. Repeat procedure for bottom portion of cover

NOTE: Check the bolts which hold the feet to the Band Saw as shown. Make sure they are tight.

2.Place the Band Saw on the Steel Legs, position as

shown and align the mountmg holes in the feet of the Band Saw with those in the END STIFFENERS (marked with an X in the illustration),

3, Mount saw to legs using four (4) 5/16-1BXl " hex head

screws, Iockwashers, and hex nuts. Tighten screws.

iNSTALLING MOTOR, PULLEY, V-BELT,

AND BELT GUARDS

1.Locate the following parrs:

Qty. Description

1 Motor

1 -L'" Bracket

LE FT

FOOT \

CHECK BOLTS

FOR

TIGHTNE_

©

00

°° 0

©

©©

o o

MOTOR

_ARD

RIGHT

FOOT

 

o

0 0

 

0 o

 

0

o

 

 

Oo

 

 

0

FRONT

OF

 

SAW HERE

0o0

SUPPORT AT

THIS END

 

SUPPORT

1Small Pulley (approx. 2-1/2" Dia.)

1Large Pulley (approx. 5" Dia )

1Woodruff Key 3/16"'

1V-Belt 1/2 x 52

1Motor Cord Clamp

4Carnage Bolt 5/16-18 x 3/4

4Flat Washer 5/16 I.D.

4Lockwasher 5/16 I.D.

4Hex Nut 5/16-18

2Guard Assembly including a guard support, guard

support bracket, self-threading screws, and clips,

2.Fasten a belt guard support to the band sawframewith

self-threading screws

3.Install clJ ps onto the guard support with long end facing you.

"_._./_ / /2 _ __-.N\l

SHAFT __-_

/

/

SELF-THREADING SCREW

Image 8
Contents SAW with Legs Motor Save This Manuat For Future ReferenceSAW only Know Your Power Tool Keep Guards in PlaceAvoid Dangerous Environment Keep Children AwayProtection Eyes, Hands, Face, Ears, Body PAG ELocation Allow Tool to Stop Before Adjusting Belt Drive Front of the Band SAW/SANDER and Front of the Blade GuardGerous Wear YourContacting the SAW Blade Volts Catalog noThis Prong Prong Receptacle AdapterUnpackmn g and checking contents Assembling Steel Legs For MountingABC Support HEX NUT LEG SCR EWINSTALLING MOTOR, PULLEY, V-BELT Belt GuardsLE FT Foot \ Right FootPulley Lockwasher Flat Washer HUB SET ScrewKEY Small 2-9/2 DIA, Motor Pulley SetscrewWrench Pulley FlushInstalling Sawdust Elbow SELF-THR Eading Screw Clamp Sawdust Elbow Rubber GasketTable Trunnion Upper BladeGuide BAR Lock Screw Guide BARUpper Thrust Bearing Setscrew Wrench SetscrewsTHRUSTBEARIN!i tl / Upper Thrust Bearing Lower Thrust BearingArms Length ScrewPointer Blade Centered On Tires Both WheelsAdjusting the Table Start of assembly section on pg for checking methodKnob ApproxON-OFF Switch For Your OWN SafetyLock Switch RkkOutlet TENS,ONAUST,NGK.OB--GUIDE BAR Lock ScrewInside Lower Knob Not ShownSquare Guide BARSetscrew Wrench BAR Combination Anding BeltSanding Platen Lockwasher PlateBasic Band SAW/SANDER Operation SawingBlade StZEGeneral Maintenance AccessoriesYour Band SAW RecommendedProbable Cause RemedyTrouble Cause RemedyTrouble Shootng TroubleProbable Cause RemedyCraftsman Inch Band SAW/SANDER Model 113.243311Parts LiSTDescription IkeypartFor Wiring Diagram Craftsman 12-INCH Band SAW/SANDER, Model 113.243300See 12 \Descr Iption KEY Part NO. noKepart Nono Suppued WiTH Model 113.243311 only Hardware for Mounting Tool & MotorSupplied WiTH Model 113.243311 only ThreadMotor Connections Strain ReliefPage Page Model no