SPECIFIC SAFETY RULES — CIRCULAR SAWS
Blade depth and bevel adjusting lock- ing levers must be tight and secure before making cut. If blade adjustment
Always observe that the lower guard is covering the blade before plac- ing saw down on bench or floor. An
1. DANGER!: |
Keep hands away from cutting area |
and blade. Keep your second hand |
on auxiliary handle or motor housing. |
If both hands are holding the saw, they |
cannot be cut by the blade. |
Do not reach underneath the work- |
piece. The guard cannot protect you |
from the blade below the workpiece. |
Adjust the cutting depth to the thick- |
ness of the workpiece. Less than a full |
tooth of the blade teeth should be visible |
below the workpiece. |
NEVER hold piece being cut in your |
hands or across your leg. Secure the |
workpiece to a stable platform. It is |
important to support the work properly to |
minimize body exposure, blade binding, |
or loss of control. |
Hold power tool by insulated grip- |
ping surfaces when performing an |
operation where the cutting tool may |
contact hidden wiring or its own cord. |
Contact with a “live” wire will also make |
exposed metal parts of the tool “live” and |
shock the operator. |
When ripping always use a rip fence |
or straight edge guide. This improves |
the accuracy of cut and reduces the |
chance of blade binding. |
Always use blades with correct size |
and shape (diamond versus round) of |
arbor holes. Blades that do not match |
the mounting hardware of the saw will |
run eccentrically, causing loss of con- |
When the blade is pinched or bound tightly by the kerf closing down, the blade stalls and the motor reaction drives the unit rapidly back toward the operator.
If the blade becomes twisted or mis- aligned in the cut, the teeth at the back edge of the blade can dig into the top surface of the wood causing the blade to climb out of the kerf and jump back toward operator.
KICKBACK is the result of saw misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below:
Maintain a firm grip with both hands on the saw and position your arms to resist kickback forces. Position your body to either side of the blade, but not in line with the blade. Kickback could cause the saw to jumb backwards, but kickback forces can be controlled by the operator, if proper precautions are taken.
When blade is binding, or when inter- rupting a cut for any reason, release the trigger and hold the saw motion- less in the material until the blade comes to a complete stop. Never attempt to remove the saw from the work or pull the saw backward while the blade is in motion or kickback may occur. Investigate and take cor- rective actions to eliminate the cause of blade binding.
shifts while cutting, it may cause binding and kickback.
Use extra caution when making a "plunge cut" (or pocket cut) into existing walls or other blind areas. The protruding blade may cut objects that can cause kickback.
3.Check lower guard for proper closing before each use. Do not operate saw if lower guard does not move freely and close instantly. Never clamp or tie the lower guard into the open po- sition. If saw is accidentally dropped, lower guard may be bent. Raise the lower guard with the lower guard lever and make sure it moves freely and does not touch the blade or any other part, in all angles and depths of cut.
Check the operation of the lower guard spring. If the guard and the spring are not operating properly, they must be serviced before use. Lower guard may operate sluggishly due to damaged parts, gummy deposits, or a buildup of debris.
Lower guard should be retracted manually only for special cuts such as "plunge cuts" ("pocket cuts") and "compound cuts". Raise lower guard by lower guard lever and as soon as blade enters the material, the lower guard must be released. For all other sawing, the lower guard should operate automatically.
unprotected, coasting blade will cause the saw to walk backwards, cutting whatever is in its path. Be aware of the time it takes for the blade to stop after switch is released.
4.Maintain labels and nameplates. These carry important information. If unreadable or missing, contact a MILWAUKEE service facility for a free replacement.
5.WARNING! Some dust created by power sanding, sawing, grinding, drill- ing, and other construction activities contains chemicals known to cause cancer, birth defects or other reproduc- tive harm. Some examples of these chemicals are:
•lead from
•crystalline silica from bricks and cement and other masonry products, and
•arsenic and chromium from chemi-
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ven- tilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
trol. |
Never use damaged or incorrect blade |
washers or bolts. The blade washers |
and bolts were specially designed for |
your saw, for optimum performance and |
safety of operation. |
2. Causes and Operator Prevention of |
KICKBACK: |
KICKBACK is a sudden reaction to |
a pinched, bound or misaligned saw |
blade, causing an uncontrolled saw to |
lift up and out of the workpiece toward |
the operator. |
When restarting a saw in the work- piece, center the saw blade in the kerf and check that saw teeth are not en- gaged into the material. If saw blade is binding, it may walk up or kickback from the workpiece as the saw is restarted.
Support large panels to minimize the risk of blade pinching and kickback. Large panels tend to sag under their own weight. Supports must be placed under the panel on both sides, near the line of cut and near the edge of the panel.
Do not use dull or damaged blade. Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding and kickback.
Symbology
Volts Direct Current
No Load Revolutions per Minute (RPM)
Underwriters Laboratories, Inc.,
United States and Canada
Specifications
Cat. | Volts | No Load | Blade | Arbor | Depth of Cut | Depth of Cut |
No. | DC | RPM | Size |
| At 90° | at 45° |
|
|
|
|
|
|
|
18 | 3200 | 5/8" | 0 to | 0 to | ||
|
|
|
|
|
|
|
4 | 5 |