Patton electronic 2635, 2603, 2621 manual Restart, Website Settings

Page 101

Models 2603, 2621, and 2635 Getting Started Guide	10 • System Configuration

Figure 75. Saving or reloading previously saved conﬁguration ﬁles

Restart

From this webpage, you can do a soft reboot of the IPLink or restore the IPLink to factory defaults. To restore to factory defaults, click on the box for Reset to factory default settings. (see ﬁgure 76.) Then click on the Restart button. No warning is given before beginning the reboot process. You will need to conﬁgure the IP address of the Ethernet port again as described in Chapter 3, Initial Conﬁguration.

Figure 76. Restoring to factory defaults

Website Settings

The refresh rate of the webpages is a conﬁgurable parameter. Enter the desired refresh rate (in seconds) and click on the Update button. Default value is 4 seconds. (See ﬁgure 77.)

Figure 77. Webpage refresh rates

Restart

101

Image 101

Contents IPLink Series High Speed Routers Mailsupport@patton.com Summary Table of Contents Contents Contents Models 2603, 2621, and 2635 Getting Started Guide Remote Site Configuration Central site configuration EMC Ethernet Cable 123 Adapter Contents Models 2603, 2621, and 2635 Getting Started Guide List of Figures Models 2603, 2621, and 2635 Getting Started Guide List of Tables Structure About this guideAudience Impaired functioning PrecautionsGeneral observations Safety when working with electricityGeneral conventions Factory default parametersTypographical conventions used in this document General Information Chapter contentsGeneral attributes IPLink Series High Speed Routers overviewProtocol support EthernetPPP Support WAN InterfacesFront Panel Status LEDs and Console Port SecurityConsole port Rear panel connectors and switchesEthernet port outlined in green Power connectorGeneral Information Product Overview Introduction Sync Serial Application Applications OverviewInitial Conﬁguration What you will need Hardware installationInterface cable installation RJ-48C pinout diagram Models 2603, 2621, and 2635 Getting Started Guide Mechanical serviceability Case being opened with a screwdriver Ethernet connector Interface connector RJ-45 DB-25 DCE Installing the AC power cordInitial Configuration Do the following Installing the Ethernet cableWeb Operation and Conﬁguration IP address modiﬁcationPC Conﬁguration Web BrowserModel 2603 home Model 2635 home Ethernet LAN Port Ethernet Port LAN ConnectionsBasic Ethernet port attributes Conﬁgurable Ethernet parameters Serial Port Conﬁguration Variables WAN Serial Port ConﬁgurationSerial Interface T1/E1 Interface Conﬁguration Web Interface ConﬁgurationWeb Conﬁguration , enter username See ﬁgure Conﬁguring the IPLink Series 2603 for T1 OperationConﬁguring the IPLink Series 2603 for E1 Operation Line Options Fractional T1Serial Port Configuration PPP Bridged WAN ServicesWAN Services PPP Bridged WAN Service ConﬁgurationPPP Conﬁguration Leave User name and Password blank. Click on Create Remote site conﬁguration PPP RoutedClick on Create Click the Update button PPP link status LMI Conﬁguration LMI Management Frame Relay linksWeb Conﬁguration Methods Dlci Number Use Frame Relay ConﬁgurationFrame Relay bridged creation Frame Relay bridgedCentral site conﬁguration Relay Frame Relay RoutedDescription FR routed Frame Relay Channel Routed conﬁguration Cost Interface frame-0 WAN Services Security Conﬁguring the router Click on Create a new serviceClick on the Create a new Ip route... hyperlink Valid gateway route Conﬁguring the security interfacesSecurity conﬁguration home Deﬁne ‘ppp-0’ interface as External Conﬁguring Security PoliciesDeleting a security Policy Enabling the FirewallFirewall Portﬁlters Add Raw IP Filter Security TriggersConﬁguring TCP port ﬁlter for FTP Adding trigger for FTP data transfer Attack Name Protocol Attacking Host Blacklisted? Intrusion Detection System IDSSecurity Global address pool and reserved map Introduction to NATEnabling NAT Click on Add Global Address Pool button Dhcp and DNS Conﬁguration Services and features normally associated with each other NAT Dhcp ServerDhcp Server web Dhcp server conﬁguration web Parameters for the Dhcp Server subnetDhcp IP address pool IP Addresses to be available on this subnetDNS server option information Example based on default range of IP address poolAdditional option information Default gateway option informationDhcp Relay Conﬁguration of the Dhcp RelayDhcp Relay webpage Conﬁguring the DNS Relay DNS RelayDNS Relay conﬁguration webpage IP Services CLI Conﬁguration IP ServicesWEB Server Associated Ports for the different System IP Services System Conﬁguration Authentication web page showing default superuser AuthenticationAccess the conﬁguration and status of the alarms AlarmAlarm & Alarm Error Log conﬁguration Remote AccessSave UpdateBackup/Restore Restart Website SettingsSnmp Daemon Error LogSnmp Daemon conﬁguration System ToolsSntp Client Conﬁguration Conﬁguring the Sntp Client Sntp Client Mode Conﬁguration ParametersSntp Client General Conﬁguration Parameters System Clock SettingConﬁguration of the internal system calendar clock System Status Port Connection Status System StatusWAN Status LAN StatusHardware Status Deﬁned InterfacesStatus LEDs Contacting Patton for assistance Patton support headquarters in the USA Warranty coverageContact information Returns for credit Out-of-warranty serviceReturn for credit policy RMA numbersEMC Appendix a Compliance informationCompliance SafetyRadio and TV Interference FCC Part CE Declaration of ConformityAuthorized European Representative Appendix B Speciﬁcations Ethernet General CharacteristicsSync Serial Interface T1/E1 InterfaceManagement Protocol SupportPPP Support Power and Power Supply Speciﬁcations DimensionsAC universal power supply VDC power supplyAppendix C Cable Recommendations Adapter Ethernet CableAppendix D IPLink Physical Connectors RJ-45 non-shielded RS-232 console port EIA-561 RJ-45 shielded 10/100 Ethernet portSerial port 35 M/34 and DB-25 ConnectorPin No Circuit Signal Name Direction 21 DB-15 ConnectorPin No Signal E1/T1 RJ-48C ConnectorAppendix E Command Line Interface CLI Operation CLI Terminology Using the ConsoleLocal VT-100 emulation Remote TelnetThen Adding new users Administering user accountsSetting user passwords Controlling user access Changing user settingsControlling login access

Related manuals

Manual 133 pages 40.62 Kb

Manual 8 pages 11.19 Kb