Patton electronic 2603, 2621, 2635 manual Remote Access, Alarm & Alarm Error Log conﬁguration

Page 99

Models 2603, 2621, and 2635 Getting Started Guide	10 • System Configuration

remain. Only by clicking on the Reset button can you clear the alarm and reset the Time and Count parame- ters. The parameter deﬁnitions are:

•Alarm Severity: there are ﬁve categories of severity-Critical, Major, Minor, Informational, and Ignore.

•Time: the time that the last alarm occurred.

•Count: the number of instances the alarm has occurred.

To conﬁgure the severity of each alarm and to conﬁgure the Alarm Error Log, click on Modify Alarms... to reach the webpage. (See ﬁgure 71.)

Figure 71. Alarm & Alarm Error Log conﬁguration

The Alarm Error Log can be enabled or disabled. The severity level of the Alarm Log can also be conﬁgured.

Similarly each alarm can be set for its own severity level.

Remote Access

The IPLink can be accessed via Telnet, known as Remote Access. The length of access over a remote connec- tion is set on this webpage. If set for zero (0), no user can access the IPLink remotely. However if a user is authorized for access, then the time is the limit before the remote access session is closed.

Figure 72. Remote Access (Telnet) access limit

Remote Access

99

Image 99

Contents IPLink Series High Speed Routers Mailsupport@patton.com Summary Table of Contents Contents Contents Models 2603, 2621, and 2635 Getting Started Guide Remote Site Configuration Central site configuration EMC Ethernet Cable 123 Adapter Contents Models 2603, 2621, and 2635 Getting Started Guide List of Figures Models 2603, 2621, and 2635 Getting Started Guide List of Tables About this guide AudienceStructure Impaired functioning PrecautionsGeneral observations Safety when working with electricityFactory default parameters Typographical conventions used in this documentGeneral conventions General Information Chapter contentsGeneral attributes IPLink Series High Speed Routers overviewWAN Interfaces EthernetProtocol support PPP SupportFront Panel Status LEDs and Console Port SecurityConsole port Rear panel connectors and switchesEthernet port outlined in green Power connectorGeneral Information Product Overview Introduction Sync Serial Application Applications OverviewInitial Conﬁguration Hardware installation Interface cable installationWhat you will need RJ-48C pinout diagram Models 2603, 2621, and 2635 Getting Started Guide Mechanical serviceability Case being opened with a screwdriver Ethernet connector Interface connector RJ-45 DB-25 DCE Installing the AC power cordInitial Configuration Do the following Installing the Ethernet cableWeb Browser IP address modiﬁcationWeb Operation and Conﬁguration PC ConﬁgurationModel 2603 home Model 2635 home Ethernet LAN Port Ethernet Port LAN ConnectionsBasic Ethernet port attributes Conﬁgurable Ethernet parameters Serial Port Conﬁguration WAN Serial Port Conﬁguration Serial InterfaceVariables T1/E1 Interface Conﬁguration Web Interface ConﬁgurationWeb Conﬁguration , enter username See ﬁgure Conﬁguring the IPLink Series 2603 for T1 OperationConﬁguring the IPLink Series 2603 for E1 Operation Line Options Fractional T1Serial Port Configuration PPP Bridged WAN ServicesWAN Services WAN Service Conﬁguration PPP ConﬁgurationPPP Bridged Leave User name and Password blank. Click on Create Remote site conﬁguration PPP RoutedClick on Create Click the Update button PPP link status LMI Conﬁguration LMI Management Frame Relay linksWeb Conﬁguration Methods Dlci Number Use Frame Relay ConﬁgurationFrame Relay bridged creation Frame Relay bridgedCentral site conﬁguration Relay Frame Relay RoutedDescription FR routed Frame Relay Channel Routed conﬁguration Cost Interface frame-0 WAN Services Security Conﬁguring the router Click on Create a new serviceClick on the Create a new Ip route... hyperlink Valid gateway route Conﬁguring the security interfacesSecurity conﬁguration home Deﬁne ‘ppp-0’ interface as External Conﬁguring Security PoliciesEnabling the Firewall Firewall PortﬁltersDeleting a security Policy Add Raw IP Filter Security TriggersConﬁguring TCP port ﬁlter for FTP Adding trigger for FTP data transfer Attack Name Protocol Attacking Host Blacklisted? Intrusion Detection System IDSSecurity Introduction to NAT Enabling NATGlobal address pool and reserved map Click on Add Global Address Pool button Dhcp and DNS Conﬁguration Services and features normally associated with each other NAT Dhcp ServerDhcp Server web Dhcp server conﬁguration web Parameters for the Dhcp Server subnetDhcp IP address pool IP Addresses to be available on this subnetDNS server option information Example based on default range of IP address poolConﬁguration of the Dhcp Relay Default gateway option informationAdditional option information Dhcp RelayDhcp Relay webpage Conﬁguring the DNS Relay DNS RelayDNS Relay conﬁguration webpage IP Services IP Services WEB ServerCLI Conﬁguration Associated Ports for the different System IP Services System Conﬁguration Authentication web page showing default superuser AuthenticationAccess the conﬁguration and status of the alarms AlarmAlarm & Alarm Error Log conﬁguration Remote AccessUpdate Backup/RestoreSave Restart Website SettingsSnmp Daemon Error LogSnmp Daemon conﬁguration System ToolsSntp Client Conﬁguration Conﬁguring the Sntp Client Sntp Client Mode Conﬁguration ParametersSntp Client General Conﬁguration Parameters System Clock SettingConﬁguration of the internal system calendar clock System Status Port Connection Status System StatusDeﬁned Interfaces LAN StatusWAN Status Hardware StatusStatus LEDs Contacting Patton for assistance Warranty coverage Contact informationPatton support headquarters in the USA RMA numbers Out-of-warranty serviceReturns for credit Return for credit policyEMC Appendix a Compliance informationCE Declaration of Conformity SafetyCompliance Radio and TV Interference FCC PartAuthorized European Representative Appendix B Speciﬁcations T1/E1 Interface General CharacteristicsEthernet Sync Serial InterfaceProtocol Support PPP SupportManagement VDC power supply DimensionsPower and Power Supply Speciﬁcations AC universal power supplyAppendix C Cable Recommendations Adapter Ethernet CableAppendix D IPLink Physical Connectors RJ-45 non-shielded RS-232 console port EIA-561 RJ-45 shielded 10/100 Ethernet portSerial port 35 M/34 and DB-25 ConnectorPin No Circuit Signal Name Direction 21 DB-15 ConnectorPin No Signal E1/T1 RJ-48C ConnectorAppendix E Command Line Interface CLI Operation Remote Telnet Using the ConsoleCLI Terminology Local VT-100 emulationThen Administering user accounts Setting user passwordsAdding new users Changing user settings Controlling login accessControlling user access

Related manuals

Manual 133 pages 40.62 Kb

Manual 8 pages 11.19 Kb