Patton electronic 2621, 2603, 2635 manual Web Interface Conﬁguration, T1/E1 Interface Conﬁguration

Page 46

Models 2603, 2621, and 2635 Getting Started Guide	5 • Serial Port Configuration

Web Interface Conﬁguration

The following screen capture shows the variables available to conﬁgure the X.21 serial interface.

Figure 21. Model 2621 X.21 serial port conﬁguration parameters

The next ﬁgure shows the Model 2635 (V.35) serial port conﬁguration parameters.

Figure 22. Model 2635 V.35 serial port conﬁguration parameters

After the serial port has been conﬁgured, go to “WAN Service Conﬁguration” on page 52 section “WAN Ser- vice Conﬁguration” on page 52 for router/bridge and WAN service conﬁguration.

T1/E1 Interface Conﬁguration

The IPLink Series Model 2603 is equipped with a user selectable T1/E1 interface. The T1 interface is pre- sented on an RJ-48C (100-ohm) connector, while the E1 interface can use the RJ-48C (120-ohm) or dual BNC (75-ohm) connectors.

The 2603 T1/E1 serial port conﬁguration page appears in ﬁgure 23.

WAN Serial Port Configuration

46

Image 46

Contents IPLink Series High Speed Routers Mailsupport@patton.com Summary Table of Contents Contents Contents Models 2603, 2621, and 2635 Getting Started Guide Remote Site Configuration Central site configuration EMC Ethernet Cable 123 Adapter Contents Models 2603, 2621, and 2635 Getting Started Guide List of Figures Models 2603, 2621, and 2635 Getting Started Guide List of Tables Audience About this guideStructure Precautions Impaired functioningSafety when working with electricity General observationsTypographical conventions used in this document Factory default parametersGeneral conventions Chapter contents General InformationIPLink Series High Speed Routers overview General attributesPPP Support EthernetProtocol support WAN InterfacesSecurity Front Panel Status LEDs and Console PortRear panel connectors and switches Console portPower connector Ethernet port outlined in greenGeneral Information Product Overview Introduction Applications Overview Sync Serial ApplicationInitial Conﬁguration Interface cable installation Hardware installationWhat you will need RJ-48C pinout diagram Models 2603, 2621, and 2635 Getting Started Guide Mechanical serviceability Case being opened with a screwdriver Ethernet connector Interface connector RJ-45 DB-25 Installing the AC power cord DCEInitial Configuration Installing the Ethernet cable Do the followingPC Conﬁguration IP address modiﬁcationWeb Operation and Conﬁguration Web BrowserModel 2603 home Model 2635 home Ethernet LAN Port LAN Connections Ethernet PortBasic Ethernet port attributes Conﬁgurable Ethernet parameters Serial Port Conﬁguration Serial Interface WAN Serial Port ConﬁgurationVariables Web Interface Conﬁguration T1/E1 Interface ConﬁgurationConﬁguring the IPLink Series 2603 for T1 Operation Web Conﬁguration , enter username See ﬁgureLine Options Fractional T1 Conﬁguring the IPLink Series 2603 for E1 OperationSerial Port Configuration WAN Services PPP BridgedWAN Services PPP Conﬁguration WAN Service ConﬁgurationPPP Bridged Leave User name and Password blank. Click on Create PPP Routed Remote site conﬁgurationClick on Create Click the Update button PPP link status LMI Management Frame Relay links LMI ConﬁgurationWeb Conﬁguration Methods Frame Relay Conﬁguration Dlci Number UseFrame Relay bridged Frame Relay bridged creationCentral site conﬁguration Frame Relay Routed RelayDescription FR routed Frame Relay Channel Routed conﬁguration Cost Interface frame-0 WAN Services Security Click on Create a new service Conﬁguring the routerClick on the Create a new Ip route... hyperlink Conﬁguring the security interfaces Valid gateway routeSecurity conﬁguration home Conﬁguring Security Policies Deﬁne ‘ppp-0’ interface as ExternalFirewall Portﬁlters Enabling the FirewallDeleting a security Policy Security Triggers Add Raw IP FilterConﬁguring TCP port ﬁlter for FTP Adding trigger for FTP data transfer Intrusion Detection System IDS Attack Name Protocol Attacking Host Blacklisted?Security Enabling NAT Introduction to NATGlobal address pool and reserved map Click on Add Global Address Pool button Dhcp and DNS Conﬁguration Services and features normally associated with each other Dhcp Server NATDhcp Server web Parameters for the Dhcp Server subnet Dhcp server conﬁguration webIP Addresses to be available on this subnet Dhcp IP address poolExample based on default range of IP address pool DNS server option informationDhcp Relay Default gateway option informationAdditional option information Conﬁguration of the Dhcp RelayDhcp Relay webpage DNS Relay Conﬁguring the DNS RelayDNS Relay conﬁguration webpage IP Services WEB Server IP ServicesCLI Conﬁguration Associated Ports for the different System IP Services System Conﬁguration Authentication Authentication web page showing default superuserAlarm Access the conﬁguration and status of the alarmsRemote Access Alarm & Alarm Error Log conﬁgurationBackup/Restore UpdateSave Website Settings RestartError Log Snmp DaemonSystem Tools Snmp Daemon conﬁgurationSntp Client Conﬁguration Sntp Client Mode Conﬁguration Parameters Conﬁguring the Sntp ClientSystem Clock Setting Sntp Client General Conﬁguration ParametersConﬁguration of the internal system calendar clock System Status System Status Port Connection StatusHardware Status LAN StatusWAN Status Deﬁned InterfacesStatus LEDs Contacting Patton for assistance Contact information Warranty coveragePatton support headquarters in the USA Return for credit policy Out-of-warranty serviceReturns for credit RMA numbersAppendix a Compliance information EMCRadio and TV Interference FCC Part SafetyCompliance CE Declaration of ConformityAuthorized European Representative Appendix B Speciﬁcations Sync Serial Interface General CharacteristicsEthernet T1/E1 InterfacePPP Support Protocol SupportManagement AC universal power supply DimensionsPower and Power Supply Speciﬁcations VDC power supplyAppendix C Cable Recommendations Ethernet Cable AdapterAppendix D IPLink Physical Connectors RJ-45 shielded 10/100 Ethernet port RJ-45 non-shielded RS-232 console port EIA-56135 M/34 and DB-25 Connector Serial port21 DB-15 Connector Pin No Circuit Signal Name DirectionE1/T1 RJ-48C Connector Pin No SignalAppendix E Command Line Interface CLI Operation Local VT-100 emulation Using the ConsoleCLI Terminology Remote TelnetThen Setting user passwords Administering user accountsAdding new users Controlling login access Changing user settingsControlling user access

Related manuals

Manual 133 pages 40.62 Kb

Manual 8 pages 11.19 Kb