Patton electronic 2621, 2635 WAN Services, Conﬁguring the IPLink Series 2603 for E1 Operation

Page 51

Models 2603, 2621, and 2635 Getting Started Guide	6 • WAN Services

WAN Services

Conﬁguring the IPLink Series 2603 for E1 Operation

Web Conﬁguration. Launch Internet Explorer or similar web browser, type the IP address of the 2603, enter username superuser and password superuser. From the main page click on the T1/E1 > Conﬁguration. (See ﬁgure 26.)

Figure 26. E1 port conﬁguration

Time Slot Select. For unframed E1 service (Clear Channel) go to the “Line Option” parameter and select “Clear Channel E1 (G.703).” For a full framed E1 enter 1-31, for partially ﬁlled E1 enter the range of timeslots using the format for example: 1,2,3,5; or 1-5,10-31. Any entry for timeslots above 31 will return and invalid selection message.

Line Options: Choose from Clear Channel E1(G.703) or Channelized E1(G.703/G.704). Consult with your service provider which option is required.

Line Code: Choose from AMI or HDB3. Most E1 applications use HDB3.

Line Build Out: Select 120 Ohms if the E1 connection is made via the RJ-48C connector, select 75 Ohm if the E1 connection is made via the dual BNC connectors.

FDL Mode: FDL is a T1 application, therefore select ‘Fdl- none’ for E1 applications.

Clocking Mode: Options are Internal or Receive Recover Clock (network). In most applications clocking for the 2603 will be derived from the E1 network, set the unit for Receive Recover unless instructed otherwise by your service provider.

Idle code: Options are Enabled or Disabled. When idle code is Enabled, the 2603 inserts idle codes (7E hex) on unused timeslots. Set this option to Disabled unless instructed otherwise.

Power Down: Options are Normal and Powerdown. When powered down, the E1 will put high impedance on the input and output lines to protect the device—set unit to Normal for regular operation.

WAN Services

51

Image 51

Contents IPLink Series High Speed Routers Mailsupport@patton.com Summary Table of Contents Contents Contents Models 2603, 2621, and 2635 Getting Started Guide Remote Site Configuration Central site configuration EMC Ethernet Cable 123 Adapter Contents Models 2603, 2621, and 2635 Getting Started Guide List of Figures Models 2603, 2621, and 2635 Getting Started Guide List of Tables About this guide AudienceStructure Impaired functioning PrecautionsGeneral observations Safety when working with electricityFactory default parameters Typographical conventions used in this documentGeneral conventions General Information Chapter contentsGeneral attributes IPLink Series High Speed Routers overviewWAN Interfaces EthernetProtocol support PPP SupportFront Panel Status LEDs and Console Port SecurityConsole port Rear panel connectors and switchesEthernet port outlined in green Power connectorGeneral Information Product Overview Introduction Sync Serial Application Applications OverviewInitial Conﬁguration Hardware installation Interface cable installationWhat you will need RJ-48C pinout diagram Models 2603, 2621, and 2635 Getting Started Guide Mechanical serviceability Case being opened with a screwdriver Ethernet connector Interface connector RJ-45 DB-25 DCE Installing the AC power cordInitial Configuration Do the following Installing the Ethernet cableWeb Browser IP address modiﬁcationWeb Operation and Conﬁguration PC ConﬁgurationModel 2603 home Model 2635 home Ethernet LAN Port Ethernet Port LAN ConnectionsBasic Ethernet port attributes Conﬁgurable Ethernet parameters Serial Port Conﬁguration WAN Serial Port Conﬁguration Serial InterfaceVariables T1/E1 Interface Conﬁguration Web Interface ConﬁgurationWeb Conﬁguration , enter username See ﬁgure Conﬁguring the IPLink Series 2603 for T1 OperationConﬁguring the IPLink Series 2603 for E1 Operation Line Options Fractional T1Serial Port Configuration PPP Bridged WAN ServicesWAN Services WAN Service Conﬁguration PPP ConﬁgurationPPP Bridged Leave User name and Password blank. Click on Create Remote site conﬁguration PPP RoutedClick on Create Click the Update button PPP link status LMI Conﬁguration LMI Management Frame Relay linksWeb Conﬁguration Methods Dlci Number Use Frame Relay ConﬁgurationFrame Relay bridged creation Frame Relay bridgedCentral site conﬁguration Relay Frame Relay RoutedDescription FR routed Frame Relay Channel Routed conﬁguration Cost Interface frame-0 WAN Services Security Conﬁguring the router Click on Create a new serviceClick on the Create a new Ip route... hyperlink Valid gateway route Conﬁguring the security interfacesSecurity conﬁguration home Deﬁne ‘ppp-0’ interface as External Conﬁguring Security PoliciesEnabling the Firewall Firewall PortﬁltersDeleting a security Policy Add Raw IP Filter Security TriggersConﬁguring TCP port ﬁlter for FTP Adding trigger for FTP data transfer Attack Name Protocol Attacking Host Blacklisted? Intrusion Detection System IDSSecurity Introduction to NAT Enabling NATGlobal address pool and reserved map Click on Add Global Address Pool button Dhcp and DNS Conﬁguration Services and features normally associated with each other NAT Dhcp ServerDhcp Server web Dhcp server conﬁguration web Parameters for the Dhcp Server subnetDhcp IP address pool IP Addresses to be available on this subnetDNS server option information Example based on default range of IP address poolConﬁguration of the Dhcp Relay Default gateway option informationAdditional option information Dhcp RelayDhcp Relay webpage Conﬁguring the DNS Relay DNS RelayDNS Relay conﬁguration webpage IP Services IP Services WEB ServerCLI Conﬁguration Associated Ports for the different System IP Services System Conﬁguration Authentication web page showing default superuser AuthenticationAccess the conﬁguration and status of the alarms AlarmAlarm & Alarm Error Log conﬁguration Remote AccessUpdate Backup/RestoreSave Restart Website SettingsSnmp Daemon Error LogSnmp Daemon conﬁguration System ToolsSntp Client Conﬁguration Conﬁguring the Sntp Client Sntp Client Mode Conﬁguration ParametersSntp Client General Conﬁguration Parameters System Clock SettingConﬁguration of the internal system calendar clock System Status Port Connection Status System StatusDeﬁned Interfaces LAN StatusWAN Status Hardware StatusStatus LEDs Contacting Patton for assistance Warranty coverage Contact informationPatton support headquarters in the USA RMA numbers Out-of-warranty serviceReturns for credit Return for credit policyEMC Appendix a Compliance informationCE Declaration of Conformity SafetyCompliance Radio and TV Interference FCC PartAuthorized European Representative Appendix B Speciﬁcations T1/E1 Interface General CharacteristicsEthernet Sync Serial InterfaceProtocol Support PPP SupportManagement VDC power supply DimensionsPower and Power Supply Speciﬁcations AC universal power supplyAppendix C Cable Recommendations Adapter Ethernet CableAppendix D IPLink Physical Connectors RJ-45 non-shielded RS-232 console port EIA-561 RJ-45 shielded 10/100 Ethernet portSerial port 35 M/34 and DB-25 ConnectorPin No Circuit Signal Name Direction 21 DB-15 ConnectorPin No Signal E1/T1 RJ-48C ConnectorAppendix E Command Line Interface CLI Operation Remote Telnet Using the ConsoleCLI Terminology Local VT-100 emulationThen Administering user accounts Setting user passwordsAdding new users Changing user settings Controlling login accessControlling user access

Related manuals

Manual 133 pages 40.62 Kb

Manual 8 pages 11.19 Kb