Patton electronic 2635, 2603, 2621 manual LAN Connections, Ethernet Port

Page 41

Models 2603, 2621, and 2635 Getting Started Guide

4 • Ethernet LAN Port

 

 

Introduction

The Ethernet LAN interface/port can be configured with two IP addresses, a primary and a secondary IP address. The configuration web page is found by following the path -> Services Configuration (in the Configu- ration Menu) -> LAN -> ‘Change default LAN port IP address’ (button on the main window).

The Basic and Advanced Port Attributes of the Ethernet LAN port is found by clicking on the Ethernet hyper- link in the IPLink’s Configuration Menu, the narrow window on the left-hand side of the web page. Clicking on the View advanced attributes... hyperlink leads to a webpage with only a few parameters that could be of interest. They are for controlling auto-negotiation, 100BaseT mode, and Full-duplex mode.

LAN Connections

The default LAN port’s IP address and netmask can be changed on this webpage. Go to -> Services Configura- tion (in the Configuration Menu) -> LAN -> ‘Change default LAN port IP address’ (button on the main window). (See figure 17.) The primary IP address and mask can be modified here, but if you do, you will no longer be able to access the IPLink’s webpages with the previous IP address. The interface associated with the Ethernet is named ip1. You can also configure a secondary IP address to the Ethernet LAN port.

Figure 17. Ethernet LAN port IP address configuration

The secondary IP address must be in the same subnet as the primary IP address. With primary and secondary IP addresses, you can reach the IPLink’s webpages via either IP address. However you will have to login for each separate IP address.

Ethernet Port

The Ethernet Port Configuration webpage provides a summary of the Ethernet port’s performance. You reach it by clicking on the hyperlink Ethernet in the IPLink’s Configuration Menu window.

The Basic Port Attributes webpage displays the most commonly used Ethernet parameters for determining the performance of the Ethernet port (see figure 18 on page 42).

Introduction

41

Page 40 Page 42
Image 41
Page 40 Page 42
Contents IPLink Series High Speed Routers Mailsupport@patton.com Summary Table of Contents Contents Contents Models 2603, 2621, and 2635 Getting Started Guide Remote Site Configuration Central site configuration EMC Ethernet Cable 123 Adapter Contents Models 2603, 2621, and 2635 Getting Started Guide List of Figures Models 2603, 2621, and 2635 Getting Started Guide List of Tables Structure About this guideAudience Impaired functioning PrecautionsGeneral observations Safety when working with electricityGeneral conventions Factory default parametersTypographical conventions used in this document General Information Chapter contentsGeneral attributes IPLink Series High Speed Routers overviewProtocol support EthernetPPP Support WAN InterfacesFront Panel Status LEDs and Console Port SecurityConsole port Rear panel connectors and switchesEthernet port outlined in green Power connectorGeneral Information Product Overview Introduction Sync Serial Application Applications OverviewInitial Configuration What you will need Hardware installationInterface cable installation RJ-48C pinout diagram Models 2603, 2621, and 2635 Getting Started Guide Mechanical serviceability Case being opened with a screwdriver Ethernet connector Interface connector RJ-45 DB-25 DCE Installing the AC power cordInitial Configuration Do the following Installing the Ethernet cableWeb Operation and Configuration IP address modificationPC Configuration Web BrowserModel 2603 home Model 2635 home Ethernet LAN Port Ethernet Port LAN ConnectionsBasic Ethernet port attributes Configurable Ethernet parameters Serial Port Configuration Variables WAN Serial Port ConfigurationSerial Interface T1/E1 Interface Configuration Web Interface ConfigurationWeb Configuration , enter username See figure Configuring the IPLink Series 2603 for T1 OperationConfiguring the IPLink Series 2603 for E1 Operation Line Options Fractional T1Serial Port Configuration PPP Bridged WAN ServicesWAN Services PPP Bridged WAN Service ConfigurationPPP Configuration Leave User name and Password blank. Click on Create Remote site configuration PPP RoutedClick on Create Click the Update button PPP link status LMI Configuration LMI Management Frame Relay linksWeb Configuration Methods Dlci Number Use Frame Relay ConfigurationFrame Relay bridged creation Frame Relay bridgedCentral site configuration Relay Frame Relay RoutedDescription FR routed Frame Relay Channel Routed configuration Cost Interface frame-0 WAN Services Security Configuring the router Click on Create a new serviceClick on the Create a new Ip route... hyperlink Valid gateway route Configuring the security interfacesSecurity configuration home Define ‘ppp-0’ interface as External Configuring Security PoliciesDeleting a security Policy Enabling the FirewallFirewall Portfilters Add Raw IP Filter Security TriggersConfiguring TCP port filter for FTP Adding trigger for FTP data transfer Attack Name Protocol Attacking Host Blacklisted? Intrusion Detection System IDSSecurity Global address pool and reserved map Introduction to NATEnabling NAT Click on Add Global Address Pool button Dhcp and DNS Configuration Services and features normally associated with each other NAT Dhcp ServerDhcp Server web Dhcp server configuration web Parameters for the Dhcp Server subnetDhcp IP address pool IP Addresses to be available on this subnetDNS server option information Example based on default range of IP address poolAdditional option information Default gateway option informationDhcp Relay Configuration of the Dhcp RelayDhcp Relay webpage Configuring the DNS Relay DNS RelayDNS Relay configuration webpage IP Services CLI Configuration IP ServicesWEB Server Associated Ports for the different System IP Services System Configuration Authentication web page showing default superuser AuthenticationAccess the configuration and status of the alarms AlarmAlarm & Alarm Error Log configuration Remote AccessSave UpdateBackup/Restore Restart Website SettingsSnmp Daemon Error LogSnmp Daemon configuration System ToolsSntp Client Configuration Configuring the Sntp Client Sntp Client Mode Configuration ParametersSntp Client General Configuration Parameters System Clock SettingConfiguration of the internal system calendar clock System Status Port Connection Status System StatusWAN Status LAN StatusHardware Status Defined InterfacesStatus LEDs Contacting Patton for assistance Patton support headquarters in the USA Warranty coverageContact information Returns for credit Out-of-warranty serviceReturn for credit policy RMA numbersEMC Appendix a Compliance informationCompliance SafetyRadio and TV Interference FCC Part CE Declaration of ConformityAuthorized European Representative Appendix B Specifications Ethernet General CharacteristicsSync Serial Interface T1/E1 InterfaceManagement Protocol SupportPPP Support Power and Power Supply Specifications DimensionsAC universal power supply VDC power supplyAppendix C Cable Recommendations Adapter Ethernet CableAppendix D IPLink Physical Connectors RJ-45 non-shielded RS-232 console port EIA-561 RJ-45 shielded 10/100 Ethernet portSerial port 35 M/34 and DB-25 ConnectorPin No Circuit Signal Name Direction 21 DB-15 ConnectorPin No Signal E1/T1 RJ-48C ConnectorAppendix E Command Line Interface CLI Operation CLI Terminology Using the ConsoleLocal VT-100 emulation Remote TelnetThen Adding new users Administering user accountsSetting user passwords Controlling user access Changing user settingsControlling login access
Related manuals
Manual 133 pages 40.62 Kb Manual 8 pages 11.19 Kb
Top Page Image Contents