Patton electronic 2621, 2603, 2635 manual Dhcp Server web

Page 85

Models 2603, 2621, and 2635 Getting Started Guide

8 • DHCP and DNS Configuration

 

 

Figure 55. DHCP Server web page

The server needs to have a subnet of IP addresses which will be allocated when a DHCP client makes a request. Define the subnet by clicking on the hyperlink Create new Subnet... The next webpage, ‘Create new DHCP Server subnet’ has four sections.

•Parameters for this subnet: defines the subnet and netmask, the origin of the subnet, maximum lease time, and default lease time.

•IP addresses to be available on this subnet: either define the IP address range for the DHCP server IP pool, or use the default range which is a set of 20 IP addresses.

•DNS server option information: enter the IP addresses of the primary and secondary DNS servers which are provided to the DHCP clients.

•Default gateway option information: You may use the local host as the default gateway.

figure 56 shows the entire configuration web page for the DHCP server.

Introduction

85

Page 84 Page 86
Image 85
Page 84 Page 86
Contents IPLink Series High Speed Routers Mailsupport@patton.com Summary Table of Contents Contents Contents Models 2603, 2621, and 2635 Getting Started Guide Remote Site Configuration Central site configuration EMC Ethernet Cable 123 Adapter Contents Models 2603, 2621, and 2635 Getting Started Guide List of Figures Models 2603, 2621, and 2635 Getting Started Guide List of Tables Audience About this guideStructure Impaired functioning PrecautionsGeneral observations Safety when working with electricityTypographical conventions used in this document Factory default parametersGeneral conventions General Information Chapter contentsGeneral attributes IPLink Series High Speed Routers overviewProtocol support EthernetPPP Support WAN InterfacesFront Panel Status LEDs and Console Port SecurityConsole port Rear panel connectors and switchesEthernet port outlined in green Power connectorGeneral Information Product Overview Introduction Sync Serial Application Applications OverviewInitial Configuration Interface cable installation Hardware installationWhat you will need RJ-48C pinout diagram Models 2603, 2621, and 2635 Getting Started Guide Mechanical serviceability Case being opened with a screwdriver Ethernet connector Interface connector RJ-45 DB-25 DCE Installing the AC power cordInitial Configuration Do the following Installing the Ethernet cableWeb Operation and Configuration IP address modificationPC Configuration Web BrowserModel 2603 home Model 2635 home Ethernet LAN Port Ethernet Port LAN ConnectionsBasic Ethernet port attributes Configurable Ethernet parameters Serial Port Configuration Serial Interface WAN Serial Port ConfigurationVariables T1/E1 Interface Configuration Web Interface ConfigurationWeb Configuration , enter username See figure Configuring the IPLink Series 2603 for T1 OperationConfiguring the IPLink Series 2603 for E1 Operation Line Options Fractional T1Serial Port Configuration PPP Bridged WAN ServicesWAN Services PPP Configuration WAN Service ConfigurationPPP Bridged Leave User name and Password blank. Click on Create Remote site configuration PPP RoutedClick on Create Click the Update button PPP link status LMI Configuration LMI Management Frame Relay linksWeb Configuration Methods Dlci Number Use Frame Relay ConfigurationFrame Relay bridged creation Frame Relay bridgedCentral site configuration Relay Frame Relay RoutedDescription FR routed Frame Relay Channel Routed configuration Cost Interface frame-0 WAN Services Security Configuring the router Click on Create a new serviceClick on the Create a new Ip route... hyperlink Valid gateway route Configuring the security interfacesSecurity configuration home Define ‘ppp-0’ interface as External Configuring Security PoliciesFirewall Portfilters Enabling the FirewallDeleting a security Policy Add Raw IP Filter Security TriggersConfiguring TCP port filter for FTP Adding trigger for FTP data transfer Attack Name Protocol Attacking Host Blacklisted? Intrusion Detection System IDSSecurity Enabling NAT Introduction to NATGlobal address pool and reserved map Click on Add Global Address Pool button Dhcp and DNS Configuration Services and features normally associated with each other NAT Dhcp ServerDhcp Server web Dhcp server configuration web Parameters for the Dhcp Server subnetDhcp IP address pool IP Addresses to be available on this subnetDNS server option information Example based on default range of IP address poolAdditional option information Default gateway option informationDhcp Relay Configuration of the Dhcp RelayDhcp Relay webpage Configuring the DNS Relay DNS RelayDNS Relay configuration webpage IP Services WEB Server IP ServicesCLI Configuration Associated Ports for the different System IP Services System Configuration Authentication web page showing default superuser AuthenticationAccess the configuration and status of the alarms AlarmAlarm & Alarm Error Log configuration Remote AccessBackup/Restore UpdateSave Restart Website SettingsSnmp Daemon Error LogSnmp Daemon configuration System ToolsSntp Client Configuration Configuring the Sntp Client Sntp Client Mode Configuration ParametersSntp Client General Configuration Parameters System Clock SettingConfiguration of the internal system calendar clock System Status Port Connection Status System StatusWAN Status LAN StatusHardware Status Defined InterfacesStatus LEDs Contacting Patton for assistance Contact information Warranty coveragePatton support headquarters in the USA Returns for credit Out-of-warranty serviceReturn for credit policy RMA numbersEMC Appendix a Compliance informationCompliance SafetyRadio and TV Interference FCC Part CE Declaration of ConformityAuthorized European Representative Appendix B Specifications Ethernet General CharacteristicsSync Serial Interface T1/E1 InterfacePPP Support Protocol SupportManagement Power and Power Supply Specifications DimensionsAC universal power supply VDC power supplyAppendix C Cable Recommendations Adapter Ethernet CableAppendix D IPLink Physical Connectors RJ-45 non-shielded RS-232 console port EIA-561 RJ-45 shielded 10/100 Ethernet portSerial port 35 M/34 and DB-25 ConnectorPin No Circuit Signal Name Direction 21 DB-15 ConnectorPin No Signal E1/T1 RJ-48C ConnectorAppendix E Command Line Interface CLI Operation CLI Terminology Using the ConsoleLocal VT-100 emulation Remote TelnetThen Setting user passwords Administering user accountsAdding new users Controlling login access Changing user settingsControlling user access
Related manuals
Manual 133 pages 40.62 Kb Manual 8 pages 11.19 Kb
Top Page Image Contents