Patton electronic 2603, 2621, 2635 manual Installing the Ethernet cable, Do the following

Page 36

Models 2603, 2621, and 2635 Getting Started Guide	3 • Initial Configuration

Power

		Gateway
	ipLink	Router
2603
WAN
ModelSpeed	Console
High	Console

				100M	Rx
			Link	Tx
	Frame	RD	Link
	Frame	RD	Ethernet
Link	TD
	WAN

Model 2603 ipLink Gateway

High Speed WAN Access Router

Power	Link FrameTD RD
	WAN

Link 100MTx Rx

Ethernet

Console

	Power	WAN Link WAN TD		Ethernet	Ethernet Tx	Ethernet Rx	Console
	LED
		LED	LED	Link	LED	LED	port

		WAN Frame	WAN RD LED		Ethernet
		LED	LED		100M
					LED

Figure 13. IPLink front panel LEDs and Console port locations (Model 2603 shown)

Installing the Ethernet cable

Do the following:

The interconnecting cables shall be acceptable for external use and shall be rated for the proper application with respect to volt- age, current, anticipated temperature, ﬂammability, and

CAUTION mechanical serviceability.

1.Connect the DB9-RJ45 adapter to the DB-9 serial port on the PC or dumb terminal. Use the RJ45-RJ45 straight-through cable between the adapter and the red marked RJ45 port on the IPLink Router.

2.Do not connect the router to the Ethernet LAN at this time.

3.On the PC, start a terminal emulation session (such as TeraTerm or HyperTerminal) at 9600 bps, 8 data bits, 1 stop bit, and no parity.

4.Plug the AC power cord into The IPLink Series router to power up the router.

5.Type superuser for Login:, and press Enter.

6.Then type superuser for the password, press Enter.

Hardware installation

36

Image 36

Contents IPLink Series High Speed Routers Mailsupport@patton.com Summary Table of Contents Contents Contents Models 2603, 2621, and 2635 Getting Started Guide Remote Site Configuration Central site configuration EMC Ethernet Cable 123 Adapter Contents Models 2603, 2621, and 2635 Getting Started Guide List of Figures Models 2603, 2621, and 2635 Getting Started Guide List of Tables About this guide AudienceStructure Precautions Impaired functioningSafety when working with electricity General observationsFactory default parameters Typographical conventions used in this documentGeneral conventions Chapter contents General InformationIPLink Series High Speed Routers overview General attributesEthernet Protocol supportPPP Support WAN InterfacesSecurity Front Panel Status LEDs and Console PortRear panel connectors and switches Console portPower connector Ethernet port outlined in greenGeneral Information Product Overview Introduction Applications Overview Sync Serial ApplicationInitial Conﬁguration Hardware installation Interface cable installationWhat you will need RJ-48C pinout diagram Models 2603, 2621, and 2635 Getting Started Guide Mechanical serviceability Case being opened with a screwdriver Ethernet connector Interface connector RJ-45 DB-25 Installing the AC power cord DCEInitial Configuration Installing the Ethernet cable Do the followingIP address modiﬁcation Web Operation and ConﬁgurationPC Conﬁguration Web BrowserModel 2603 home Model 2635 home Ethernet LAN Port LAN Connections Ethernet PortBasic Ethernet port attributes Conﬁgurable Ethernet parameters Serial Port Conﬁguration WAN Serial Port Conﬁguration Serial InterfaceVariables Web Interface Conﬁguration T1/E1 Interface ConﬁgurationConﬁguring the IPLink Series 2603 for T1 Operation Web Conﬁguration , enter username See ﬁgureLine Options Fractional T1 Conﬁguring the IPLink Series 2603 for E1 OperationSerial Port Configuration WAN Services PPP BridgedWAN Services WAN Service Conﬁguration PPP ConﬁgurationPPP Bridged Leave User name and Password blank. Click on Create PPP Routed Remote site conﬁgurationClick on Create Click the Update button PPP link status LMI Management Frame Relay links LMI ConﬁgurationWeb Conﬁguration Methods Frame Relay Conﬁguration Dlci Number UseFrame Relay bridged Frame Relay bridged creationCentral site conﬁguration Frame Relay Routed RelayDescription FR routed Frame Relay Channel Routed conﬁguration Cost Interface frame-0 WAN Services Security Click on Create a new service Conﬁguring the routerClick on the Create a new Ip route... hyperlink Conﬁguring the security interfaces Valid gateway routeSecurity conﬁguration home Conﬁguring Security Policies Deﬁne ‘ppp-0’ interface as ExternalEnabling the Firewall Firewall PortﬁltersDeleting a security Policy Security Triggers Add Raw IP FilterConﬁguring TCP port ﬁlter for FTP Adding trigger for FTP data transfer Intrusion Detection System IDS Attack Name Protocol Attacking Host Blacklisted?Security Introduction to NAT Enabling NATGlobal address pool and reserved map Click on Add Global Address Pool button Dhcp and DNS Conﬁguration Services and features normally associated with each other Dhcp Server NATDhcp Server web Parameters for the Dhcp Server subnet Dhcp server conﬁguration webIP Addresses to be available on this subnet Dhcp IP address poolExample based on default range of IP address pool DNS server option informationDefault gateway option information Additional option informationDhcp Relay Conﬁguration of the Dhcp RelayDhcp Relay webpage DNS Relay Conﬁguring the DNS RelayDNS Relay conﬁguration webpage IP Services IP Services WEB ServerCLI Conﬁguration Associated Ports for the different System IP Services System Conﬁguration Authentication Authentication web page showing default superuserAlarm Access the conﬁguration and status of the alarmsRemote Access Alarm & Alarm Error Log conﬁgurationUpdate Backup/RestoreSave Website Settings RestartError Log Snmp DaemonSystem Tools Snmp Daemon conﬁgurationSntp Client Conﬁguration Sntp Client Mode Conﬁguration Parameters Conﬁguring the Sntp ClientSystem Clock Setting Sntp Client General Conﬁguration ParametersConﬁguration of the internal system calendar clock System Status System Status Port Connection StatusLAN Status WAN StatusHardware Status Deﬁned InterfacesStatus LEDs Contacting Patton for assistance Warranty coverage Contact informationPatton support headquarters in the USA Out-of-warranty service Returns for creditReturn for credit policy RMA numbersAppendix a Compliance information EMCSafety ComplianceRadio and TV Interference FCC Part CE Declaration of ConformityAuthorized European Representative Appendix B Speciﬁcations General Characteristics EthernetSync Serial Interface T1/E1 InterfaceProtocol Support PPP SupportManagement Dimensions Power and Power Supply SpeciﬁcationsAC universal power supply VDC power supplyAppendix C Cable Recommendations Ethernet Cable AdapterAppendix D IPLink Physical Connectors RJ-45 shielded 10/100 Ethernet port RJ-45 non-shielded RS-232 console port EIA-56135 M/34 and DB-25 Connector Serial port21 DB-15 Connector Pin No Circuit Signal Name DirectionE1/T1 RJ-48C Connector Pin No SignalAppendix E Command Line Interface CLI Operation Using the Console CLI TerminologyLocal VT-100 emulation Remote TelnetThen Administering user accounts Setting user passwordsAdding new users Changing user settings Controlling login accessControlling user access

Related manuals

Manual 133 pages 40.62 Kb

Manual 8 pages 11.19 Kb