Southbend SB1017 owner manual Controls, Blade Tension Knob Adjusts the position

Page 22

Model SB1017

O P E R A T I O N

For Machines Mfg. Since 8/09

Controls

Refer to Figures 20–21and the following descriptions to become familiar with the basic controls of this machine.

A. Blade Tension Knob: Adjusts the position
	of the upper blade wheel to apply or release
	blade tension.
B.	Guide Post Knob: Locks the guide post in
	the position set by the operator.
C.	Downfeed Rate Adjust Knob: Controls
	the speed at which the blade lowers into the
	workpiece.
D.	Downfeed Valve: Controls the starting and
	stopping of the headstock downfeed.
E.	Work Stop Lock Knob: Locks the work stop

I.Head Locking Pin: Can be inserted into one of three holes to lock the head in the down, up, or vertical positions.

J.Vise Jaw Lock Bolt: Locks the vise jaw at the angle set by the operator.

K.Feed Pressure Handle: Controls the feed pressure by increasing or decreasing preload on the feed pressure spring.

L.Transport Handle: Provides a solid control point for moving the machine.

M.Fence Scale: Indicates the angle of the vise fence.

N.Vise Fence Bolts (behind fence): Lock the fence at the angle set by the operator.

	in the position set by the operator.
F.	ON/OFF Toggle Switch: Turns the saw
	motor ON or OFF.
G.	Vise Jaw Handwheel: Controls the vise jaw
	movement.
H.	Downfeed Stop Bolt: Adjusts to determine
	the absolute bottom limit of blade travel.

I

N

J K

M

L

B C

A

G	F	H

D

E

Figure 20. Front Identification.

Figure 21. Rear Identification.

-20-

Image 22

Contents

Bandsaw Scope of Manual UpdatesCustomer Service Manual FeedbackTable of Contents About This Machine FeaturesCapabilities Identification ON/OFFMachine Specifications Machine SpecificationsMain Specifications Operation Information Basic Machine Safety Understanding Risks of MachineryF E T Y Additional Metal Bandsaw Safety Availability Required for SetupPower Supply Requirements Full-Load Current RatingCircuit Requirements for For 110V Connection PrewiredCircuit Information Grounding RequirementsExtension Cords Unpacking InventoryAssembly To assemble the bandsawLoosen the belt tension bolt shown in Figure Installing belt Before cleaning, gather the following Cleaning & ProtectingBasic steps for removing rust preventative Location Test Run Power ConnectionInspections Adjustments To test run your machineOperationPERATIONOverview ON/OFF Toggle Switch Turns the saw Blade Tension Knob Adjusts the positionDownfeed Rate Adjust Knob Controls ControlsBlade Length Blade SelectionBlade Terminology Blade WidthTooth Set Tooth TypeBlade Pitch TPI To select the correct blade pitchBlade Changes To change the blade on the bandsawTo tension the blade on the bandsaw Blade TensionBlade Breakage Most common causes of avoidable blade breakage areBlade Care Blade Care & Break-InBlade Speed Blade Break-InBlade Speed Chart Chip Inspection ChartDownfeed Rate To install and use the work stopDownfeed Pressure Work StopVise To use the viseVertical Cutting To adjust the blade guideBlade Guide To convert the saw for vertical cuttingHorizontal Cutting Operation TipsVertical Cutting Accessories SBL Gearhead T-Shirt SBL One Good Turn T-ShirtLubrication CleaningGearbox Machine Storage Belt ReplacementTo replace the V-belt Downfeed Stop Bolt To adjust the blade tracking on the bandsawBlade Tracking To adjust the blade guide bearings Blade Guide BearingsAuto-OFF Tab To adjust the auto-OFF tabSquaring Blade To square the blade to the tableModel SB1017TROUBLESHOOTING For Machines Mfg. Since 8/09 Troubleshooting Dull blade missing teeth Replace blade ElectricalL CTRICALSafety Instructions Wiring Diagram Color KEY220V Conversion To convert the Model SB1017 toWiring Diagram 110VR T S Cabinet Stand Head Head Parts List PK23MMotor & Blade Guides Motor & Blade Guides Parts List Plastic WasherSwitch Machine Labels PSBLABEL15S Electricity LabelT E S R R a N T Y Southbendlathe.com

Related manuals

Manual 56 pages 14.11 Kb